05-10-2005
Sco Unix error while booting
Hi RTM,
I looked at the link that u sent me.But i never reloaded any new OS nor did i do something with the EISA config. I remember that i removed some of the connections in the system and then reconnected them.Since then i had been getting this error.
Can u please eloborate and help me out ? what do i do now to rectify this problem ?
thanks in advance
Veera
10 More Discussions You Might Find Interesting
1. SCO
hi, i m a newbie and installed sco unix on my machine. Also i installed win-xp. i tried to modify the boot.ini file but it does not give me a choice in the begining.
please guide me on this. do we get a boot loader for unix like LILO or GRUB?
:confused: (3 Replies)
Discussion started by: 187final
3 Replies
2. SCO
anyone know where I can download or get a boot disk for sco unix v/386? I have an old PC running sco unix v/386 3.2. I dont have an install or boot disk. I need to reset the root password. I have looked all over the internet and cannot find it anywhere. any help would be greatly appreciated.... (5 Replies)
Discussion started by: format
5 Replies
3. SCO
Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused:
my old pc is a Pentium II 333mhz 3gb hd 64mb ram
please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies
4. SCO
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Discussion started by: jedimaster
86 Replies
5. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
6. UNIX for Dummies Questions & Answers
UNIX sco release 5.05 system does not boot:cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/bootWhat to do? (2 Replies)
Discussion started by: Joaoalpande
2 Replies
7. SCO
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (1 Reply)
Discussion started by: Joaoalpande
1 Replies
8. UNIX for Advanced & Expert Users
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (5 Replies)
Discussion started by: Joaoalpande
5 Replies
9. SCO
HI All,
I have an old SCO-UNIX machine which I support a long standing client / friend with.
I don't use it very often, and is kept switched off. All was well 2 weeks ago, but when I tried to boot today all I get is a continuous set of long beeps but no booting. I have checked inside... (4 Replies)
Discussion started by: andy sleight
4 Replies
10. SCO
hi
i have image SCo Unix 5.0.6 and I want transfer on my HP ML350 G5
after Transfer show this message :
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
this hp server used smart array E200i and P400 and sco not recognized HDD
tanks (7 Replies)
Discussion started by: moein.mojtaba
7 Replies
LEARN ABOUT OSF1
do_config
do_config(9r) do_config(9r)
NAME
do_config - EISA/ISA: Initializes the device to its assigned configuration
SYNOPSIS
void do_config(
struct controller *ctlr_p );
ARGUMENTS
Specifies a pointer to the controller structure associated with the controller to be configured. The do_config routine obtains the device
to initialize through its controller's associated controller structure pointer.
DESCRIPTION
The do_config routine initializes the specified controller based on its power-up resource assignments. If the device uses either an inter-
rupt or a DMA channel, then do_config also performs any setup requirements. For example, for controllers that connect to the EISA bus,
do_config initializes the controller according to the parameters specified in the EISA configuration file.
NOTES
The do_config routine is a generic interface that maps to a bus-specific interface that actually initializes the specified device. Using
this routine to initialize a device makes the driver more portable across different bus architectures. Not all buses support the do_config
routine.
RETURN VALUES
None
SEE ALSO
Routines: get_config(9r), get_info(9r)
Data Structures: controller(9s)
do_config(9r)