Sponsored Content
Full Discussion: Dynamic routing table
Operating Systems AIX Dynamic routing table Post 71131 by jdsnbr on Friday 6th of May 2005 03:31:45 PM
Old 05-06-2005
Question Dynamic routing table

i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.

thanks
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

not following routing table

Hi, I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies

2. IP Networking

routing table (netstat -rn)

Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system. Thanks! (4 Replies)
Discussion started by: thundrrod
4 Replies

3. IP Networking

Ip routing table

hi all, how to access ip routing table throgh program, how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies

4. IP Networking

routing table

hi all... i need to know, where is locate the routing table on sun solaris, how i can saved the configuration.... because when i restart the server, lost the configuration.... thank you... Regards... (3 Replies)
Discussion started by: chanfle
3 Replies

5. IP Networking

Routing table

Hi all, I am confusing with routing table, i use linux and iptables. i have 1 internet gateway, and 1 router for VPN. here is my network. eth0=192.168.0.1 eth1=192.168.100.1 192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet | ... (4 Replies)
Discussion started by: blesets
4 Replies

6. Linux

Routing Table

Hello, how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies

7. UNIX for Advanced & Expert Users

Sql dynamic table / dynamic inserts

I have a file that reads File (X.txt) Contents of record 1: rdrDESTINATION_ADDRESS (String) "91 971502573813" rdrDESTINATION_IMSI (String) "000000000000000" rdrORIGINATING_ADDRESS (String) "d0 movies" rdrORIGINATING_IMSI (String) "000000000000000" rdrTRAFFIC_EVENT_TIME... (0 Replies)
Discussion started by: magedfawzy
0 Replies

8. Red Hat

routing table question

I have below routing table in linux kernel 2.6.9 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies

9. UNIX for Dummies Questions & Answers

Linux - how to turn on the the RIP (dynamic routing)

(3 Replies)
Discussion started by: samnyc
3 Replies
SYSTEMD-TIMESYNCD.SERVICE(8)				     systemd-timesyncd.service				      SYSTEMD-TIMESYNCD.SERVICE(8)

NAME
systemd-timesyncd.service, systemd-timesyncd - Network Time Synchronization SYNOPSIS
systemd-timesyncd.service /lib/systemd/systemd-timesyncd DESCRIPTION
systemd-timesyncd is a system service that may be used to synchronize the local system clock with a remote Network Time Protocol server. It also saves the local time to disk every time the clock has been synchronized and uses this to possibly advance the system realtime clock on subsequent reboots to ensure it monotonically advances even if the system lacks a battery-buffered RTC chip. The systemd-timesyncd service specifically implements only SNTP. This minimalistic service will set the system clock for large offsets or slowly adjust it for smaller deltas. More complex use cases are not covered by systemd-timesyncd. The NTP servers contacted are determined from the global settings in timesyncd.conf(5), the per-link static settings in .network files, and the per-link dynamic settings received over DHCP. See systemd.network(5) for more details. timedatectl(1)'s set-ntp command may be used to enable and start, or disable and stop this service. FILES
/var/lib/systemd/timesync/clock This file contains the timestamp of the last successful synchronization. SEE ALSO
systemd(1), timesyncd.conf(5), systemd.network(5), systemd-networkd.service(8), timedatectl(1), localtime(5), hwclock(8) systemd 237 SYSTEMD-TIMESYNCD.SERVICE(8)
All times are GMT -4. The time now is 03:17 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy