09-17-2001
unable to bring up any interface
I have Linux 7.1 setup on a Dell and am unable to bring up any interfaces. Both the lo and eth0 fail upon boot up and I get a insmod error possibly due to bad irq or IO setting.
If I disable eth0 upon boot, then lo works fine, but offcourse I get the "delaying initialization" upon boot for eth0
help
thanks
Last edited by alam; 09-17-2001 at 11:09 AM..
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies
2. Solaris
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies
3. IP Networking
Hi
(sorry for my bad English)
I'm trying to configure an US Robotics (USR5423) wirless usb adapter on Fedora 9. the device is detected, and i'm trying to configure a wireless connection.
When I want to activate the device using
#service network restart
or
# /etc/init.d/network restart... (0 Replies)
Discussion started by: teis
0 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)
NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) ifsysctl(8)
sysconfig December 2009 IFNDP-PROXY(5)