This is HP-UX specific and I will move it to the HP-UX forum at some point.
I prefer ioscan over lanscan. There is also "netstat -i". But the lanadmin command in interactive mode will show the most info. Below, I show them all in use. What I typed is in green. Some important info is in red. A few remarks that I added are in blue.
Code:
Script started on Tue Apr 5 10:17:03 2005
# netstat -i
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Coll
lan2 1500 192.168.49.0 zxcvbnm1 890529567 0 2366045846 0 0
lo0 4136 loopback localhost 126109 0 126109 0 0
# lanscan
Hardware Station Crd Hdw Net-Interface NM MAC HP-DLPI DLPI
Path Address In# State NamePPA ID Type Support Mjr#
0/1/2/0 0x00306EF4542C 0 UP lan0 snap0 1 ETHER Yes 119
0/5/1/0/6/0 0x00306E4C5E40 2 UP lan2 snap2 2 ETHER Yes 119 So PPA of lan2 really is 2 (almost always the case)
0/5/2/0/6/0 0x00306E4C8E5B 3 UP lan3 snap3 3 ETHER Yes 119
0/2/1/0 0x00306EEAB301 1 UP lan1 snap1 4 ETHER Yes 119
0/6/1/0 0x00306EEAD39B 4 UP lan4 snap4 5 ETHER Yes 119
# ioscan -fC lan
Class I H/W Path Driver S/W State H/W Type Description
========================================================================
lan 0 0/1/2/0 igelan CLAIMED INTERFACE HP A6825-60101 PCI 1000Base-T Adapter
lan 1 0/2/1/0 btlan CLAIMED INTERFACE HP A5230A/B5509BA PCI 10/100Base-TX Addon
lan 2 0/5/1/0/6/0 igelan CLAIMED INTERFACE HP A9782-60001 PCI/PCI-X 1000Base-SX FC/GigE Combo Adapter
lan 3 0/5/2/0/6/0 igelan CLAIMED INTERFACE HP A9782-60001 PCI/PCI-X 1000Base-SX FC/GigE Combo Adapter
lan 4 0/6/1/0 btlan CLAIMED INTERFACE HP A5230A/B5509BA PCI 10/100Base-TX Addon
# lanadmin
LOCAL AREA NETWORK ONLINE ADMINISTRATION, Version 1.0
Tue , Apr 5,2005 10:18:07
Copyright 1994 Hewlett Packard Company.
All rights are reserved.
Test Selection mode.
lan = LAN Interface Administration
menu = Display this menu
quit = Terminate the Administration
terse = Do not display command menu
verbose = Display command menu
Enter command: lan
LAN Interface test mode. LAN Interface PPA Number = 0
clear = Clear statistics registers
display = Display LAN Interface status and statistics registers
end = End LAN Interface Administration, return to Test Selection
menu = Display this menu
ppa = PPA Number of the LAN Interface
quit = Terminate the Administration, return to shell
reset = Reset LAN Interface to execute its selftest
specific = Go to Driver specific menu
Enter command: ppa
Enter PPA Number. Currently 0: 2From lan2 above
LAN Interface test mode. LAN Interface PPA Number = 2
clear = Clear statistics registers
display = Display LAN Interface status and statistics registers
end = End LAN Interface Administration, return to Test Selection
menu = Display this menu
ppa = PPA Number of the LAN Interface
quit = Terminate the Administration, return to shell
reset = Reset LAN Interface to execute its selftest
specific = Go to Driver specific menu
Enter command: display
LAN INTERFACE STATUS DISPLAY
Tue , Apr 5,2005 10:18:25
PPA Number = 2
Description = lan2 HP PCI-X 1000Base-SX Release B.11.11.11
Type (value) = ethernet-csmacd(6)
MTU Size = 1500
Speed = 1000000000
Station Address = 0x306e4c5e40
Administration Status (value) = up(1)
Operation Status (value) = up(1)
Last Change = 369050172
Inbound Octets = 671979624
Inbound Unicast Packets = 725393819
Inbound Non-Unicast Packets = 15786530
Inbound Discards = 40
Inbound Errors = 0
Inbound Unknown Protocols = 313244
Outbound Octets = 190507938
Outbound Unicast Packets = 2208637279
Outbound Non-Unicast Packets = 203891
Outbound Discards = 0
Outbound Errors = 0
Outbound Queue Length = 1
Specific = 655367
Press <Return> to continue
Ethernet-like Statistics Group
Index = 2
Alignment Errors = 0
FCS Errors = 0
Single Collision Frames = 0
Multiple Collision Frames = 0
Deferred Transmissions = 0
Late Collisions = 0
Excessive Collisions = 0
Internal MAC Transmit Errors = 0
Carrier Sense Errors = 0
Frames Too Long = 0
Internal MAC Receive Errors = 0
LAN Interface test mode. LAN Interface PPA Number = 2
clear = Clear statistics registers
display = Display LAN Interface status and statistics registers
end = End LAN Interface Administration, return to Test Selection
menu = Display this menu
ppa = PPA Number of the LAN Interface
quit = Terminate the Administration, return to shell
reset = Reset LAN Interface to execute its selftest
specific = Go to Driver specific menu
Enter command: quit
#
script done on Tue Apr 5 10:18:37 2005
Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Hi All,
I have an interface port configured to a FBOL server. This port receives requests from various hosts. I want to know at any moment of time ip addresses of all those hosts from which the requests are coming in. Please help me with command/script. (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
I have scheduled couple of shell scripts to run using 'at' command.
The o/p of at -l is:
$ at -l
1320904800.a Thu Nov 10 01:00:00 2011
1320894000.a Wed Nov 9 22:00:00 2011
1320876000.a Wed Nov 9 17:00:00 2011
$ uname -a
SunOS dc2prcrptetl2 5.9 Generic_122300-54 sun4u sparc... (2 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Team,
Presently I have a script, which i have set up cron on one of my Jump-boxes,and gives me the output on every hourly basis,fetching the data from the remote machine.Basically it gives me the list of all active users logged and its count once we execute the script.Here the count is... (6 Replies)
04-05-2005