03-30-2005
3c905b network card problem with SCO 5.0.5
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice versa. I have noticed as well that terminal 1 locks at this point. I checked the /usr/adm/messages file to see if the system is writing a message of some sort about the error but nothing. Can anyone shed some light on this?
Thanks in advance.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
Hi
I just installed linux red hat 7.0 and i can't connect the machine on the network.
Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize.
Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies
3. UNIX for Dummies Questions & Answers
I've installed mandrake 9 and from the start my network card wouldn't work. I ran the network configuration wizard several times and counldn't get it to work. I checked Linux and in the boot message said the IRQ for my network card was 0 but wheni checked windows XP it listed it as 23. I have a... (1 Reply)
Discussion started by: ripmc
1 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. SCO
hello, i am new to unix and need support</SPAN></SPAN>
</SPAN></SPAN>The problem is:
I have a SCO 5.0.5 server, and has no local network access, I think my problem are the drivers for network card.
my network card is Kingston EtheRx PCI Fast Ethernet Adapter KNE120TX and already installed the... (9 Replies)
Discussion started by: daniel_cie
9 Replies
9. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT DEBIAN
opensc-tool
OPENSC-TOOL(1) OpenSC tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--info, -i
Print information about OpenSC, such as version and enabled components
--atr, -a
Print the Answer To Reset (ATR) of the card, output is in hex byte format
--name, -n
Print the name of the inserted card (driver)
--serial
Print the card serial number (normally the ICCSN), output is in hex byte format
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF...
--list-files, -f
Recursively lists all files stored on card
--list-readers, -l
Lists all configured readers
--list-drivers, -D
Lists all installed card drivers
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--wait, -w
Wait for a card to be inserted
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
SEE ALSO
opensc-explorer(1)
opensc 06/03/2012 OPENSC-TOOL(1)