Disable Network cards under boot Prom Post: 68001

Sponsored Content

Operating Systems Solaris Disable Network cards under boot Prom Post 68001 by pressy on Wednesday 30th of March 2005 06:17:27 AM

03-30-2005

Registered User

well, there is a possibility to disable the card, but if you only want to boot from another card you could ably a new alias to the other card. perhabs there is a other alias like net1 (devalias) for the other card....
ok devalias net
net /pci@1c,600000/network@2,1:
ok nvalias net /pci@1c,600000/network@3,1:
ok nvstore
ok setenv use-nvramrc? true
ok reset-all
...
..
.
ok boot net - install

or are you talking about the server. there you can define your networkcard in your jumpstartserver profile (something like iface= .. not sure)

obp:
----------attention----------
---!not_recommended!---
ok nvedit
0: probe-all install-console banner
1: " /pci@1c,600000/network@2" $delete-device drop
2:
^C
Type "Ctrl-C" to exit nvedit as shown above. Then continue with:
ok nvstore
ok setenv use-nvramrc? true
use-nvramrc? = true
ok reset-all

!! /pci@1c,600000/network@2 is the path to MY network card, take a look at your path !!

greetings pressy

pressy

View Public Profile for pressy

Find all posts by pressy

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell...

2. Solaris

How to List all Network cards

Hi, I'm looking for a command to be able to list all my network cards available on my server. With the command "ifconfig - a", I can only see to configured network card(s) Any idea ? :confused: Thanks a lot for your help, Fabien

3. AIX

Load balancing across network cards

The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer?

4. Solaris

How to find network cards available ...

Hi all, I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output. Today, this server is using the on board network connection (Ce0). How can I find the other...

5. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe...

6. Solaris

Network cards - Routing

Hi all I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem. So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1)....

7. Hardware

Slackware 13.1 can't configure two network cards

Hello everybody, I'm having troubles with Slackware 13.1 and network cards. I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the...

8. Solaris

Open Boot PROM - OK Prompt +dd +mount

Greetings friends, I would like to 'clone' the system/root hard disk with dd. (Solaris 10 on SPARC). If I understood correctly, 'OK Prompt' can use dd command? Can it mount drives? (to avoid any possibility of cloning the wrong drive, I'd like to output dd to file) thanks.

9. UNIX for Dummies Questions & Answers

1 Server with 2 ethernet cards IP on seperate network. Possible?

Hi All, I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They...

LEARN ABOUT CENTOS

opensc-tool

OPENSC-TOOL(1)							   OpenSC Tools 						    OPENSC-TOOL(1)

NAME

       opensc-tool - generic smart card utility

SYNOPSIS

       opensc-tool [OPTIONS]

DESCRIPTION

       The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
       sending arbitrary APDU commands to a card.

OPTIONS

       --atr, -a
	   Print the Answer To Reset (ATR) of the card. Output is in hex byte format

       --card-driver driver, -c driver
	   Use the given card driver. The default is auto-detected.

       --info, -i
	   Print information about OpenSC, such as version and enabled components.

       --list-drivers, -D
	   List all installed card drivers.

       --list-files, -f
	   Recursively list all files stored on card.

       --list-readers, -l
	   List all configured readers.

       --name, -n
	   Print the name of the inserted card (driver).

       --reader num, -r num
	   Use the given reader number. The default is 0, the first reader in the system.

       --send-apdu apdu, -s apdu
	   Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....

       --serial
	   Print the card serial number (normally the ICCSN). Output is in hex byte format

       --verbose, -v
	   Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.

       --wait, -w
	   Wait for a card to be inserted.

SEE ALSO

       opensc-explorer(1)

opensc								    06/17/2014							    OPENSC-TOOL(1)