How can I change the default gateway? Post: 67849

9 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

script to change default route when primary gateway dies

Hello all! We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our...

2. AIX

Help with Default Gateway

Hi, I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1. I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know...

3. Solaris

Change gateway without reboot server

Hi Gurus Recently i had change the gateway for a server i had change the IP in the /etc/defaultrouter and run the below command # route add default 10.86.33.222 # route delete default 10.86.33.1 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref ...

4. HP-UX

where can i modify default gateway

where in configuration files can i modify default gateway in hp-ux11iv3

5. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ...

6. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a...

7. Red Hat

Change Default gateway

Hi..I have to change default gateway in my linux machine. Its OS is RHEL6. I followed following steps. 1.run command ip route to check current default gateway 2.delete that gateway with command route del default gw x.x.x.x eth2 3.Add new gatewy with command below route add default gateway...

8. IP Networking

Default Gateway

I am am using IPv6 IP's with an OS of Debian. Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected? TIA

9. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different....

LEARN ABOUT SUSE

tgt-setup-lun

tgt-setup-lun(8)					      System Manager's Manual						  tgt-setup-lun(8)

NAME

       tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target

SYNOPSIS

       tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]

DESCRIPTION

       Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
       iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.

       The  script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
       tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.

EXAMPLES

       Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
       tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81

       Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
       tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82

       Create a target that uses /dev/sdb1 and allows connections from any initiator:
       tgt-setup-lun -d /dev/sdb1 -n my_target

       Display help:
       tgt-setup-lun -h

AUTHOR

       Written by Erez Zilber

REPORTING BUGS

       Report bugs to <erezz@voltaire.com>.

COPYRIGHT

       Copyright (C) Voltaire Ltd. 2008.

																  tgt-setup-lun(8)