Sponsored Content
Full Discussion: Sun Machine Rebooted
Top Forums UNIX for Dummies Questions & Answers Sun Machine Rebooted Post 6487 by Neo on Wednesday 5th of September 2001 03:48:54 PM
Old 09-05-2001
How dirty is the motherboard and hardware? Sometimes the years of dust and other grime can get between connections, especially host adapters and other end cards.

Is the inside of the machine clean? Have you taken the parts apart, cleaned and reassembled (if old)?

Also, is this a SCSI bus? Wierd things can happen with SCSI.
 

10 More Discussions You Might Find Interesting

1. Solaris

How can i Configure TCP Keepalive on sun solaris 9 machine?

I've installed sun solaris 9 and i need to know how can i enable TCP Keepalive to ping socket connections every 300 seconds? Thanks, Mohammed Amin (1 Reply)
Discussion started by: m_amin
1 Replies

2. Solaris

how to change IP of my SUN solaris machine

Hello, I want to change the IP of my SUN solaris machine but i am not bale to find the right way. I tried the following steps: 1) edit /etc/inet/hosts and change IP address for host listed in /etc/hostname.le0 2) ifconfig le0 down 3) ifconfig le0 inet NEW_IP_ADDR netmask + broadcast + ... (5 Replies)
Discussion started by: er_aparna
5 Replies

3. Solaris

Sun machine boot up

Hi I am trying to bring up our Sun V100 machine remotely using hyper terminal. We have connected LOM port A to COM1 of our windows server and have lom promt available. Now when we type poweron it starts booting and goes through the booting process and stops at the following step... .... ... (7 Replies)
Discussion started by: chimpu
7 Replies

4. Solaris

Installation os on sun machine

I had one sun ultra enterprise1 cpu. it's not giving any disply,which operating system it's support. How can install os on this CPU. (2 Replies)
Discussion started by: jagadeesh
2 Replies

5. Solaris

Sun Machine Crashed

During system startup the following warnings are appear. Warning: /pci@8, 700000/scsi@6, 1 (g1m1) Connected command timeout for target 9.0 Warning: /pci@8, 700000/scsi@6, 1 (g1m1) Target 9 reducing sync, transfer rate Warning: /pci@8, 700000/scsi@6, 1... (5 Replies)
Discussion started by: tabreaz
5 Replies

6. Solaris

How to configure IP in SUN Machine

Hi Experts, I am new for solaris, i am using Solaris10,can you anyone assist me how to configure IP in my machine. Thanks (4 Replies)
Discussion started by: daya.pandit
4 Replies

7. Solaris

Sun is not able to ssh another machine of sun

My one Sun machine is not able to ssh another machine of Sun. Although I have configured the ssh successfully ( SunOS sunbox2 5.9 Generic_118558-34 sun4u sparc SUNW,Sun-Blade-2500 ) ERROR bash-2.05# ssh sunbox2 /etc/ssh/ssh_config: line 34: Bad configuration option: PermitRootLogin... (0 Replies)
Discussion started by: z_haseeb
0 Replies

8. Solaris

Old Sun machine documentation needed

Hi all. Last year, after registering on Sun support site, I downloaded for free all available documentation (in PDF) and support files of a couple of old Sun workstations (Ultra 5 and Ultra 10). Now I need the documentation and support files of other old Sun workstations (SPARCstation 20 and... (4 Replies)
Discussion started by: wisechip
4 Replies

9. UNIX for Beginners Questions & Answers

Cloned Sun OS 10 HD using replicator machine

Dear all, I have Sun Oracle 10 SPARC T4-1 machine with 4 units SAS2 300GB configure with 2 set Raid1. Is it possible to take out all 4 hd and cloned the 4 HD using disk clone/replicator machine with same HD size and model? After the cloned completed put back the new cloned HD at original... (4 Replies)
Discussion started by: ayyahma
4 Replies

10. UNIX for Beginners Questions & Answers

Start /SYS on SUN SPARC does not start machine [SUN SPARC ENTERPRISE T-5240]

-> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS ]-> show HOST /HOST Targets: bootmode diag domain Properties: autorestart = reset autorunonerror = false bootfailrecovery = poweroff ... (29 Replies)
Discussion started by: z_haseeb
29 Replies
MCA(4)							   BSD Kernel Interfaces Manual 						    MCA(4)

NAME
mca -- introduction to machine-independent MCA bus support and drivers SYNOPSIS
mca0 at mainbus? options MCAVERBOSE Machine-dependent; depends on the bus topology and MCA bus interface of your system. Typical MCA buses are connected directly to the main system bus. DESCRIPTION
NetBSD includes a machine-independent MCA bus subsystem and several machine-independent MCA device drivers. HARDWARE
NetBSD includes machine-independent MCA drivers, sorted by device type and driver name: SCSI controllers aha Adaptec AHA-1640 SCSI interface esp NCR 53C90 SCSI Adapter Disk and tape controllers edc IBM ESDI Fixed Disk Controller Serial interfaces com NS8250-, NS16450-, and NS16550-based serial cards. Network interfaces tr TROPIC based token ring interfaces ate Allied-Telesis 1720 Ethernet interface cards we WD/SMC WD80x3x Ethernet interface cards and clones le SKNET Personal and MC+ Ethernet interface cards elmc 3Com EtherLink/MC (3c523) Ethernet interface ep 3Com EtherLink III 3c529 Ethernet interface tra Tiara LANCard/E and Standard MicroSystems 3016/MC Ethernet interface SEE ALSO
aha(4), ate(4), com(4), edc(4), elmc(4), ep(4), esp(4), le(4), ne(4), tr(4), tra(4), we(4) HISTORY
The machine-independent MCA subsystem appeared in NetBSD 1.5. BSD
March 3, 2005 BSD
All times are GMT -4. The time now is 06:26 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy