02-06-2005
Thanks Manu,
Can I use any PCI ehternet card or does it have to be an IBM card. Specifically I have a 3COM Fast Etherlnk XL PCI 10/100 BASE TX (3C905B-TX) adapter I wanted to use. I downloaded drivers for this card from IBM but the README states that if the card isn't IBM's version it won't work... I guess I could just try it anyway. Have any ideas? Thanks.
Jeff
10 More Discussions You Might Find Interesting
1. AIX
I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Discussion started by: rahe
0 Replies
2. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
3. SuSE
Hey all, ive got redhat 80 and trying to install a HCF win modem. Ive intsalled the drivers from linuxant.com using the rpm - i packagename.rpm command, but i still cant use the modem
any suggestions ? (3 Replies)
Discussion started by: kiwi_bloke
3 Replies
4. Solaris
hello mates,
do you know a manufactor for rs232 serial pci cards for the sparc architecture? it seems that there is no original product from sun for that purpose. strange, isn't it?
problem is that i have a V250 with only one db9 rs232 serial port, and i need it for a modem connection, but i also... (1 Reply)
Discussion started by: pressy
1 Replies
5. UNIX for Dummies Questions & Answers
I have a US Robotics USR5416 wireless networking card and everytime after hours of inactivity the cardseems to shutdown. I read somewhere the it does not support power management. Is there a way to disable power management to that particular PCI card? (0 Replies)
Discussion started by: diesel440
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
8. Solaris
Hello all,
I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant.
My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows:
#grep e1000... (2 Replies)
Discussion started by: kerrygold
2 Replies
9. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
10. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT REDHAT
pcitweak
PCITWEAK(1) General Commands Manual PCITWEAK(1)
NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platfoms pcitweak can only
be run by the root user.
OPTIONS
-l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO
scanpci(1)
AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version Version 4.3.0 PCITWEAK(1)