Sponsored Content
Full Discussion: Internet Connection via Lan
Operating Systems Solaris Internet Connection via Lan Post 61430 by youwantwhat on Thursday 3rd of February 2005 10:14:46 AM
Old 02-03-2005
Computer

I CAN RELATE.. I ran into the same problem less than a week ago.. below is the items I checked to correct the issue.

make sure your port is turned on in your firewall (80 for HTTP, 4?? for HTTPS)

* your host table
/etc/hosts
should have your router and gateway

* your gateway:
/etc/defaultrouter
192.168.133.1

* your nameserver:
/etc/resolv.conf
search unix.com (or your ISP DNS)
nameserver 192.168.133.2
nameserver 192.168.133.3

* nameresolution:
/etc/nsswitch.conf
hosts: files dns

*** after your change these files, reboot system.
Smilie Good luck
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

setup internet connection

HI.. i was wondering if someone out there can help me setup my internet connection.... i have no clue how to set it up.. could you please tell me step by step how to set it up.. i have a static ip, im using a cable modem to connect. my os is solaris 8. Please email me at lil_souldier@hotmail.com... (2 Replies)
Discussion started by: souldier
2 Replies

2. UNIX for Advanced & Expert Users

setting up internet connection!!

HI unix guru.. i need your help again.. i tring to setup my sun box for internet connection, i am using @home cable service i have 8 pc running different operating systems. every other computer can go online but this sun box for some reason alway give me and error, i enter my ip address... (1 Reply)
Discussion started by: souldier
1 Replies

3. UNIX for Dummies Questions & Answers

solaris internet connection

Hi everyone, I just installed Solaris 10 in my PC. However, once I finished installing it, I lost my internet connection. When I switch to windows, the internet can run smoothly. Does anyone know how to set up internet connection in Solaris ? I am so sorry, I am new in UNIX (7 Replies)
Discussion started by: qqq
7 Replies

4. UNIX for Dummies Questions & Answers

Connection of SUN to internet and to PC

Hi, 1)If someone could help me out that how could i connect to internet. Below is the system specification, and i have dial up connection. Sun UltraSPARC-IIi 270MHz processor 256 MB memory 8.4 GB HDD 100/10BaseT Ethernet CD-ROM drive 3.5" Floppy drive 2)Also, how to connect Sun to... (0 Replies)
Discussion started by: younics
0 Replies

5. BSD

Internet connection with PC BSD

Hi friends! :) I have got an Acer laptop. in one of the partion's I have got PC BSD installed. I am new UNIX user coz first I was using Windows, so I am still learning it. I only know few commands, and I find it very interesting. Unfrtunately, when I log into PC BSD, I can't connect to the... (3 Replies)
Discussion started by: dubbio123
3 Replies

6. Shell Programming and Scripting

Problem establishing Connection on the LAN

Hi everybody i need your help on this I have LAN which run Sun microsystem with solaris 7 OS on each of the servers. The LAN was working fine before an interruption of power supply which makes servers to operating as standalone servers. i.e none of the servers have access to one another. How do i... (2 Replies)
Discussion started by: sbmada
2 Replies

7. Solaris

Internet connection

I got solaris 10 works, but I cannot set up my internet connection. When I ping a website and i open the web browser, it doesn't work. When the installation asked 'Am I in a network?' i answerd 'no'. I think this is my minstake. How can i get Internet, now? I have a ADSL modem (not router).... (5 Replies)
Discussion started by: mghis
5 Replies

8. Ubuntu

Ubuntu 10.10 LAN connection stopped working...

Well this is weird. I restarted my dual boot Win7/Ubuntu 10.10 from ubuntu to windows. Everything was working fine and windows is always connecting properly to my lan. After restarting back into Ubuntu, all of a sudden I can't connect to my network. It looks as if its trying to connect through... (15 Replies)
Discussion started by: zixzix01
15 Replies

9. IP Networking

Sharing internet connection

Hello all, Recently took a dive into Unix using Fedora 12 atm. I have cable modem with DHCP and a linksys 8 port router. With windows I was able to simple use the uplink port and plug each computer into the switch and use the internet connection. Having no luck doing the same in Unix. I have... (0 Replies)
Discussion started by: Fingerz
0 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 08:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy