01-27-2005
HPUX Routing Question
We have an HPUX machine that is having a routing problem. Any traffic sent on the local network (same switch) works fine. However, when we try to send traffic to any other ip the machine NAT's the ip to that of the gatway and nothing goes any further.
For example if I try to ping 10.1.1.1 from the HPUX machine, a sniffer on the network shows that the machine tries to ping the gateway address instead.
Also, if any machine off the network tries to ping the unix server, the replies get translated to the address of the gateway and do not get sent back to the sender ip address.
Please advise.
10 More Discussions You Might Find Interesting
1. IP Networking
I have SCO Unix. I have 2 routers. as it is now, when someone telnets to UNIX and goes through router #1 everything is fine. The users who go through router #2 can not connect at all. I talked to CISCO and they said I need to set up a second Gateway on UNIX. They said what is happening is that... (1 Reply)
Discussion started by: john fli
1 Replies
2. IP Networking
ok i configured my gateway and IP address(es) using ifconfig and route.. but how can i bind unique IPs to users ? (im using FreeBSD 4.2 RELEASE #3) (9 Replies)
Discussion started by: DevilGREEN
9 Replies
3. UNIX for Advanced & Expert Users
Hi,
in which file and how shuold be decalred a gateway and its IP adresse ?
Where and how add a gateway ?
Many thanks before. (4 Replies)
Discussion started by: big123456
4 Replies
4. Shell Programming and Scripting
I am running HPUX and using WLM (workload manager). I want to write a script to fork CPUs to basically take CPUs from other servers to show that the communication is working and CPU licensing is working. Basically, I want to build a script that will use up CPU on a server. Any ideas? (2 Replies)
Discussion started by: cpolikowsky
2 Replies
5. HP-UX
why is that I need to go to /usr/sbin> in order to run send mail
how can I run sendmail where ever folder I'm in...
e.g. like
/stuff/games/sendmail
ksh: sendmail: not found (7 Replies)
Discussion started by: makaveli
7 Replies
6. HP-UX
Are "/dev/dsk/c58t6d7" and "/dev/dsk/c94t0d4" assigning to a same disk?
results of "vgdisplay -v"
PV Name /dev/dsk/c58t6d7
PV Name /dev/dsk/c94t0d4 Alternate Link
PV Name /dev/dsk/c75t6d7 Alternate Link
PV Name ... (1 Reply)
Discussion started by: JoyOnLine
1 Replies
7. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
8. HP-UX
I'm sharing this in case anybody needs it. Modified from the original solaris pwage script. This modified hpux script will check /etc/password file on hpux trusted systems search /tcb and grep the required u_succhg field. Calculate days to expiry and notify users via email.
original solaris... (2 Replies)
Discussion started by: sparcguy
2 Replies
9. IP Networking
Internet Gateway
192.168.0.201
Server 1
192.168.0.101
192.168.1.101
192.168.2.101
gateway: 192.168.0.201
VIP: 192.168.1.100
VIP: 192.168.2.100
Server 2
192.168.0.102
192.168.1.102
192.168.2.102
gateway: 192.168.0.201
Client 1
192.168.2.201
gateway: 192.168.2.100 (1 Reply)
Discussion started by: hopfensp
1 Replies
10. UNIX for Advanced & Expert Users
Simple question: how to package from source in hpux?
On Linux slackware i Use configure,make,make install DESTDIR=$pkg,etc..
and then makepkg -l y -c n.
Is possible something similar on hpux?
I want to create a depot for samba because,the official
doesn't had the winbind pam,and the package on... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)
NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO
mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)