01-01-2005
Alright, I understand. Thank you for clearifying that.
10 More Discussions You Might Find Interesting
1. IP Networking
We run Compaq UNIX Tru64 5.1.
After a switch got replaced our ethernet-card was magically set to
half duplex!
We saw, that the card was set to Autonegotiate:
vmunix: ee1: Autonegotiated, 100 Mbps full duplex
So we set the card with ifconfig to 100 Mbps full duplex with the
following... (3 Replies)
Discussion started by: arn_ch
3 Replies
2. UNIX for Dummies Questions & Answers
We are using ZIX 4.3.3 and we need to configure the NIC for ful duplexing and we also need to configure it for a TCP/IP default gateway and DNS server to acccess the Interent.
Can you please tell me the commands and procedures for configuring this?
Thanks
Marc (2 Replies)
Discussion started by: marc3483
2 Replies
3. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
4. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
5. Solaris
How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies
6. Red Hat
All,
I have a RedHat 9 box which I need to figure out how to get it to stay in full duplex mode after a reboot.
I have tried
ethtool -s eth0 speed 100 duplex full autoneg off
I have tried to add a line to the /etc/sysconfig/network-scripts/ifcfg-eth0 like this:
ETHTOOL_OPTS="speed... (4 Replies)
Discussion started by: bubba112557
4 Replies
7. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
8. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
9. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
10. Programming
Hello,
here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data... (3 Replies)
Discussion started by: demerzel3
3 Replies
LEARN ABOUT REDHAT
ssl_ctx_new
SSL_CTX_new(3) OpenSSL SSL_CTX_new(3)
NAME
SSL_CTX_new - create a new SSL_CTX object as framework for TLS/SSL enabled functions
SYNOPSIS
#include <openssl/ssl.h>
SSL_CTX *SSL_CTX_new(SSL_METHOD *method);
DESCRIPTION
SSL_CTX_new() creates a new SSL_CTX object as framework to establish TLS/SSL enabled connections.
NOTES
The SSL_CTX object uses method as connection method. The methods exist in a generic type (for client and server use), a server only type,
and a client only type. method can be of the following types:
SSLv2_method(void), SSLv2_server_method(void), SSLv2_client_method(void)
A TLS/SSL connection established with these methods will only understand the SSLv2 protocol. A client will send out SSLv2 client hello
messages and will also indicate that it only understand SSLv2. A server will only understand SSLv2 client hello messages.
SSLv3_method(void), SSLv3_server_method(void), SSLv3_client_method(void)
A TLS/SSL connection established with these methods will only understand the SSLv3 protocol. A client will send out SSLv3 client hello
messages and will indicate that it only understands SSLv3. A server will only understand SSLv3 client hello messages. This especially
means, that it will not understand SSLv2 client hello messages which are widely used for compatibility reasons, see SSLv23_*_method().
TLSv1_method(void), TLSv1_server_method(void), TLSv1_client_method(void)
A TLS/SSL connection established with these methods will only understand the TLSv1 protocol. A client will send out TLSv1 client hello
messages and will indicate that it only understands TLSv1. A server will only understand TLSv1 client hello messages. This especially
means, that it will not understand SSLv2 client hello messages which are widely used for compatibility reasons, see SSLv23_*_method().
It will also not understand SSLv3 client hello messages.
SSLv23_method(void), SSLv23_server_method(void), SSLv23_client_method(void)
A TLS/SSL connection established with these methods will understand the SSLv2, SSLv3, and TLSv1 protocol. A client will send out SSLv2
client hello messages and will indicate that it also understands SSLv3 and TLSv1. A server will understand SSLv2, SSLv3, and TLSv1
client hello messages. This is the best choice when compatibility is a concern.
The list of protocols available can later be limited using the SSL_OP_NO_SSLv2, SSL_OP_NO_SSLv3, SSL_OP_NO_TLSv1 options of the
SSL_CTX_set_options() or SSL_set_options() functions. Using these options it is possible to choose e.g. SSLv23_server_method() and be able
to negotiate with all possible clients, but to only allow newer protocols like SSLv3 or TLSv1.
SSL_CTX_new() initializes the list of ciphers, the session cache setting, the callbacks, the keys and certificates, and the options to its
default values.
RETURN VALUES
The following return values can occur:
NULL
The creation of a new SSL_CTX object failed. Check the error stack to find out the reason.
Pointer to an SSL_CTX object
The return value points to an allocated SSL_CTX object.
SEE ALSO
SSL_CTX_free(3), SSL_accept(3), ssl(3), SSL_set_connect_state(3)
0.9.7a 2001-07-25 SSL_CTX_new(3)