|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
TermCap Error w/Anzio SSH
Post 59796 by zazzybob on Thursday 30th of December 2004 04:55:15 PM
12-30-2004
|
|
10 More Discussions You Might Find Interesting
1. Linux
Hi.
How do I enter and escape from graphics mode on RedHat Linux to capture escape sequences. I'm trying to edit the system termcap. (2 Replies)
Discussion started by: cstovall
2 Replies
2. UNIX for Dummies Questions & Answers
Hi all!
What is the TERMCAP variable? (1 Reply)
Discussion started by: aitor314
1 Replies
3. UNIX for Dummies Questions & Answers
Hello,
I have one application (top) for Solaris that exits with error
"no entry in termcap for 'hp'".
What can I do with system to fix it? Is it access problem to termcap file or real corruption inside the file since I know that HP is defined in termcap?
...
or changes to environment... (0 Replies)
Discussion started by: gogogo
0 Replies
4. UNIX for Dummies Questions & Answers
My ncurses program has been displaying "OP" (junk) on pressing F1 (instead of catching it). I have finally discovered that it runs fine (traps F1) when run under screen (program), but not in my login terminal (xterm-color)
I did a check of "Set" and "env" under screen, there is a "TERMCAP"... (0 Replies)
Discussion started by: sentinel
0 Replies
5. HP-UX
Hi
I`ve got problem with screen.
After i launch screen i get flying list of :
---(example)
Name collision between cad68-3 cad68-3
Name collision between cad68-2 cad68-2
Name collision between cops10 cops10
Name collision between d132 d132 MH
Name collision between d800 d800 M7
Name... (4 Replies)
Discussion started by: chesti
4 Replies
6. Ubuntu
Hi all,
I am trying to install Scigraphica on Ubuntu 8.10 and Termcap needs to be installed.
I cannot find or install Termcap by Synaptic package manager (sudo apt-get install does not work either).
I found in some forums that Termcap is not available for Ubuntu 8.10, and ncurses-dev was... (0 Replies)
Discussion started by: apprentice
0 Replies
7. UNIX for Advanced & Expert Users
Hi - I am getting the error
`Error reading response length from authentication socket'
when I ssh from my cluster to another cluster, and then back to my cluster. It doesn't seem to affect anything, but it's just annoying that it always pops up and tends to confuse new users of the cluster. I... (1 Reply)
Discussion started by: cpp6f
1 Replies
8. UNIX for Advanced & Expert Users
Hi,
I'm executing the set of commands in remote machine via ssh command. But the control is not even going inside the if statement (not echo-ing anything).
/usr/bin/ssh ${2}@${1} <<EOF >/var/tmp/housekeeping_${1}_${2}_`date +%Y%m%d%H%M%S`.log
if ; then
echo -e "File system is 100%... (15 Replies)
Discussion started by: apsprabhu
15 Replies
9. UNIX for Dummies Questions & Answers
Well, apparently anyway.
I have a Solaris 10/08 install using vi (not vim) and when I use vi to edit a file or go into cron, the screen goes into 25/80 mode and I have to send a reset or hard reset to get it back to my screen size (190x72 in this case).
vi should be using the TERM environment... (7 Replies)
Discussion started by: BOFH
7 Replies
10. Red Hat
ssh -q <remote_server> <command> is not working for only one remote server.
From the source, we are able to connect other servers using the above command but one. All the servers are in same network and no selinux/iptables enabled.
The verbose output has the following message -
debug1:... (4 Replies)
Discussion started by: atanubanerji
4 Replies
LEARN ABOUT BSD
httppower
httppower(8) powerman httppower(8) NAME
httppower - communicate with HTTP based power distribution units SYNOPSIS
httppower [--url URL] DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac- tively by the powerman daemon. OPTIONS
-u, --url URL Set the base URL. INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt: auth user:pass Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password over the network in plain text. seturl URL Set the base URL. Overrides the command line option. get [URL-suffix] Send an HTTP GET to the base URL with the optional URL-suffix appended. post [URL-suffix] key=val[&key=val]... Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument. FILES
/usr/sbin/httppower /etc/powerman/powerman.conf ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms of the GNU GPL. SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7). http://sourceforge.net/projects/powerman powerman-2.3.5 2009-02-09 httppower(8)