11-12-2004
Thanks.
With "scsi sda mass storage device>>>", does it tell any partition just after it?
You can always check with /proc/partitions to make sure.
fdisk -l would do too.
10 More Discussions You Might Find Interesting
1. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
2. UNIX for Dummies Questions & Answers
How do you mount a USB flash drive on Sun Blade 2000 or 2500 with solaris 8?
Thanks in advance ;) (1 Reply)
Discussion started by: xeroxtechnician
1 Replies
3. UNIX for Advanced & Expert Users
:( If anyone has solved this problem, please help me!
Thanks in advance! (0 Replies)
Discussion started by: FCollet
0 Replies
4. UNIX for Advanced & Expert Users
If somebody solve this error please help!
Thanks in advance! (5 Replies)
Discussion started by: FCollet
5 Replies
5. UNIX for Dummies Questions & Answers
My computer which uses scoUNIX, has an internal scsi tape backup. It will
no longer backup . It posts this message Notice :Stp tape 0 device 46/0
offline. This has been discussed before by the forum and I'd appreciate any
help that any expert could provide for me for a step wise approach to... (0 Replies)
Discussion started by: timothymhubbard
0 Replies
6. UNIX for Advanced & Expert Users
My tape drive is not backing up my data. This is the message that comes up as the computer starts up each morning. Notice Stp:SCSI tape 0 device 46/0 offline. The computer is equipped with a Seagate STD 24000N internal tape drive and the green indicator light on it continuously is on but the amber... (0 Replies)
Discussion started by: timothymhubbard
0 Replies
7. Linux
Hi Folks,
I want to know how to mount usb device (cd,dvd etc) in linux,
Regards,
Manoj (4 Replies)
Discussion started by: manoj.solaris
4 Replies
8. UNIX and Linux Applications
When I attach a USB storage device to my Solaris server, the mount point is coming up as /rmdisk/unnamed_rmdisk
Is there anyway I can have this device come up as a mounted device with a predetermined mount name eg /morespace rather than unnamed_rmdisk ? (0 Replies)
Discussion started by: jimthompson
0 Replies
9. Ubuntu
Hi,
I have a created a logical partition sda5 in ubuntu server 9.0.4.
which is
Disk /dev/sda: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00053d78
Device Boot Start End ... (1 Reply)
Discussion started by: rac_oradba
1 Replies
10. Solaris
I'm looking for help with a legacy system.
I have some obsolete equipment connected to an Ultra 60 running Solaris 5.7 with the binary for a 32 bit driver. The driver is rejected by newer versions of solaris, which run 64 bit kernels.
I hope to reverse engineer the driver so that I can... (0 Replies)
Discussion started by: obsoleteStuff
0 Replies
SD(4) Linux Programmer's Manual SD(4)
NAME
sd - Driver for SCSI Disk Drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */
#include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIGURATION
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a reread of the SCSI disk partition tables. No parameter is needed.
The scsi(4) ioctl(2) operations are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl(2) will fail
with the error EINVAL.
FILES
/dev/sd[a-h]: the whole device
/dev/sd[a-h][0-8]: individual block partitions
COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 SD(4)