Sponsored Content
Full Discussion: Network card and internet
Top Forums UNIX for Dummies Questions & Answers Network card and internet Post 57816 by Gibbler on Sunday 7th of November 2004 12:58:29 PM
Old 11-07-2004
Network card and internet

Hi!.

I have problems installing my network card under
ther redhat kernel.

First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.

also i huse my network card to connect to the net
trough PPPOE where i need to type my username and
pass to gain acess to the net windows has an integrated
client for this but i can´t find any in red hat.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

5. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

9. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
DUMMY_CS(4)						     Kernel Interfaces Manual						       DUMMY_CS(4)

NAME
dummy_cs - PCMCIA dummy device driver SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...] DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set- ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers. It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions about card types, it is forced to rely on the card information, for better or worse. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. free_ports=n A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5). pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)
All times are GMT -4. The time now is 11:49 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy