Sponsored Content
Full Discussion: Configuring NIC
Operating Systems HP-UX Configuring NIC Post 57442 by wobitu on Thursday 28th of October 2004 05:08:18 AM
Old 10-28-2004
Error Configuring NIC

Hi.

I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card instead of using the old 10mb card ? Do I need to reinstall the Operating system ? I wish there is a shortest way of introducing the card.

I reaaly apprecaite your help in this matter.

VERY BEST REGARDS,
Wobitu.
 

8 More Discussions You Might Find Interesting

1. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies

2. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi (1 Reply)
Discussion started by: Remi
1 Replies

3. IP Networking

Problem configuring NIC in DGUX

Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten Unable to get NIC working Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

8. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ... (1 Reply)
Discussion started by: alphatron150
1 Replies
whois(1)						      General Commands Manual							  whois(1)

NAME
whois - Internet username directory service SYNOPSIS
whois [-h server] name... The whois command looks up user, host, and organization names in the Network Information Center (NIC) database. OPTIONS
Specifies a whois server other than the default server rs.internic.net. DESCRIPTION
The name argument can specify the following: The name of a registered user The name of a registered Internet host The name of some other entity recognized by the whois server By default, the whois command queries the host rs.internic.net. The operands specified to the whois command are concatenated together (separated by white-space) and presented to the whois the server. The default action, unless directed otherwise with a special name is to do a very broad search, looking for matches to name in all types of records and most fields (such as name, nicknames, host name, and network address) in the database. For more information as to what name operands have special meaning, and how to guide the search, use the special name help. EXAMPLES
To display the NIC database entry for the organization osf.org, enter: whois osf.org Open Software Foundation (OSF-DOM) 11 Cambridge Center Cambridge, MAS 02142 Domain Name: OSF.ORG . . . SEE ALSO
DARPA Internet Request for Comment: NICKNAME/WHOIS (RFC 812) whois(1)
All times are GMT -4. The time now is 03:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy