09-08-2004
Documentation on SUN Cluster can be found at
docs.sun.com
Last edited by RTM; 09-14-2007 at 10:07 AM..
Reason: link no longer exist - changed to just docs.sun.com
9 More Discussions You Might Find Interesting
1. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
2. Solaris
Hi,
I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly.
I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies
3. Gentoo
We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be... (9 Replies)
Discussion started by: kccrusher
9 Replies
4. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
5. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
6. Solaris
Hi All
I hav working knowledge on solarois 10.
Could anyone suggest me any doc or material for learning SUN cluster from scratch. Anything from basic level .
Thanks in advance!! (1 Reply)
Discussion started by: ningy
1 Replies
7. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
9. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_ibd
scconf_transp_adap_ibd(1M) System Administration Commands scconf_transp_adap_ibd(1M)
NAME
scconf_transp_adap_ibd - configure the InfiniBand (ibd) transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure ibd adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The ibd adapter connects to an InfiniBand transport switch. The connection is made through a transport cable.
When the endpoints of the transport cable are configured by using scconf, scinstall, or other tools, you are asked to specify a port name
on the transport switch. You can provide any port name, or accept the default, as long as the name is unique for the switch.
The default is to set the port name to the node ID that hosts the adapter at the other end of the cable.
There are no user-configurable properties for cluster transport adapters of this type.
SEE ALSO
Intro(1CL), clinterconnect(1CL), clnode(1CL), scconf(1M), scconf_transp_jct_ibswitch(1M), scinstall(1M), ibd(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ibd(1M)