08-16-2004
Use a cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector - connect this to a db25 cross cable(or Null Modem adapter) to serial_A on the sun box.
(Error 633 The port is already in use - usually a modem error -
Make sure that you are not using another program that requires that port. If not, try rebooting your PC computer.)
What are your connection settings in hyperterminal??
e.g. Comm Port?
bits per/sec = 9600
data bits = 8
parity = none
stop bits = 1
flow control = hardware
Please list.
Also do you have a keyboard plugged in to the box?
Try connecting the console cable to sun box, unplug keybd from sun and rebooting the sun box.
10 More Discussions You Might Find Interesting
1. Solaris
HI all,
i still have a problem when using null modem to see the output from my server(sun ultra en 3000).
i followed the instruction from the internet, but it is not working.
1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port).
2.... (3 Replies)
Discussion started by: waterbear
3 Replies
2. Solaris
hi all..
sorry for repeating the same question many times,
i just set up a null modem, i am using this as reference :
DB25 DB9
-- -
2 TD ---- 2 RD
3 RD ---- 3 TD
4 RTS ---- 8 CTS
5 CTS ---- 7 RTS
7 GND ---- 5 GND
6 DSR -+
+--- 4 DTR
8... (0 Replies)
Discussion started by: waterbear
0 Replies
3. Solaris
Hi all,
I currently have my WinXP machine connected to my Sun server via serial cable then hyperterminal. I would like to connect my Solaris 10 machine to the server via serial cable but there doesn't appear to be a hyperterminal application included with Solaris 10. Anyone know of a... (3 Replies)
Discussion started by: bad-ash
3 Replies
4. Solaris
Hi All,
I connected my serial connection to the installation of solaris 8 and sorry to tell you I use XP/hyperterminal, don't get mad on me... I might use ubuntu later.
When I'm installing it, it's ask me below:
What type of terminal are you using?
1) ANSI Standard CRT
2) DEC VT52
... (3 Replies)
Discussion started by: itik
3 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. AIX
I configured the serial modem in my P6-550 AIX 5.3 box
But i dont have telephone line.
when I run the command
# cu -l /dev/tty1
the output is as follows
does it mean that my modem is responding to the command?
can i say my serial port is working and communicating fine?
Connected
... (3 Replies)
Discussion started by: pchangba
3 Replies
7. Hardware
Hello,
I want to connect a VT520 terminal to p3 linux box.
I have two questions regarding the connection. First,
is it possible to use RJ45 instead of RS232
cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter).
Second point is that; do i need null modem cable or
straight cable... (5 Replies)
Discussion started by: vectrum
5 Replies
8. Solaris
hi
I am new to unix and have found a SPARCstation 5 in the shed. I'm told by my father that it was working when it was put there about 8 years ago.
It seems to boot up and makes all the right noises, both discs appear to make a noise, the keyboard lights flash etc., etc., but i can't seem to get... (2 Replies)
Discussion started by: harrystrickland
2 Replies
9. Hardware
Hello everybody,
I didn't know were to post this, so i posted here in hardware section.
I'm having some troubles while trying to interconnect two pc's via modem (soft fax modem, RJ-11 jack). One is a Handheld PC (HP Jornada 728) with a single fax modem slot, and the other computer is a PC with... (6 Replies)
Discussion started by: Zykl0n-B
6 Replies
10. Solaris
I am having troubles with carrier detection for dialing in via a modem or direct connection via a null modem connection under Solaris 8 (i.e. login session remains active after the modem disconnects). I tried two different dumb modems (which do not respond to AT commands) on the machine that I am... (6 Replies)
Discussion started by: rstor
6 Replies
LEARN ABOUT OPENSOLARIS
identify
identify(9E) Driver Entry Points identify(9E)
NAME
identify - determine if a driver is associated with a device
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI). This entry point is no longer supported. nulldev(9F) must be specified in the dev_ops(9S) structure.
SEE ALSO
nulldev(9F), dev_ops(9S)
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Stability Level |Obsolete |
+-----------------------------+-----------------------------+
WARNING
For Solaris 10 and later versions, drivers must remove the identify(9e) implementation to recompile. Otherwise, the compiler generates
errors about DDI_IDENTIFIED and DDI_NOT_IDENTIFIED.
SunOS 5.11 11 Apr 2003 identify(9E)