08-14-2004
HCF win modem PCI card
Hey all, ive got redhat 80 and trying to install a HCF win modem. Ive intsalled the drivers from linuxant.com using the rpm - i packagename.rpm command, but i still cant use the modem
any suggestions ?
9 More Discussions You Might Find Interesting
1. Solaris
hello mates,
do you know a manufactor for rs232 serial pci cards for the sparc architecture? it seems that there is no original product from sun for that purpose. strange, isn't it?
problem is that i have a V250 with only one db9 rs232 serial port, and i need it for a modem connection, but i also... (1 Reply)
Discussion started by: pressy
1 Replies
2. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
3. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
4. UNIX for Dummies Questions & Answers
I have a US Robotics USR5416 wireless networking card and everytime after hours of inactivity the cardseems to shutdown. I read somewhere the it does not support power management. Is there a way to disable power management to that particular PCI card? (0 Replies)
Discussion started by: diesel440
0 Replies
5. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
6. Solaris
Hello all,
I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant.
My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows:
#grep e1000... (2 Replies)
Discussion started by: kerrygold
2 Replies
7. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
LEARN ABOUT SUNOS
faxstate
FAXSTATE(8) System Manager's Manual FAXSTATE(8)
NAME
faxstate - control ``modem state'' of a device used by HylaFAX
SYNOPSIS
/usr/sbin/faxstate [ -q queue-dir ] [ -s state ] [ -n ] modem
DESCRIPTION
faxstate sends a message to the HylaFAX faxgetty(8) process servicing modem telling it to use the specified state when notifying the
HylaFAX scheduler that a modem is ready and available for use. This is useful for controlling outbound use of a modem; by marking a
modem's state as busy or down the HylaFAX scheduler will not assign any outbound jobs to the modem.
The specified modem can either be the name (typically the last component of the terminal port the modem is attached to), or the full name
of the associated FIFO named pipe file, e.g. ``FIFO.ttym2''.
If the -n option, faxstate emulates what faxgetty would do; sending a message directly to the faxq process marking the specified modem
down, busy, or ready. This interface is useful for send-only environments in which faxgetty processes are not used. Note that modems
manipulated in this way must previously have been configured with the faxmodem(8) program.
OPTIONS
The following options are supported:
-n Contact faxq directly instead of faxgetty.
-q dir Use a spooling area other than /var/spool/hylafax.
-s Specify the state to send the faxq process each time the modem becomes ready for use; one of ``busy'', ``down'', and ``ready''.
The default state to use is ready.
FILES
Consult hylafax-server(5) for a complete discussion of the structure and content of the spooling area.
SEE ALSO
hylafax-server(5), faxgetty(8)
July 17, 1995 FAXSTATE(8)