08-08-2004
CAT5 is just normal ethernet cable.
What you need to do is connect router1 to router2, as if router2 was just another PC.
Take a piece of ethernet cable (not a crossover cable) and plug on end into the uplink port on router1 and the other end into an ethernet port on router2.
7 More Discussions You Might Find Interesting
1. IP Networking
There is a small company with 3 locations in Idaho. Currently they are using UNIX with multiplexors from 10 years ago. They would like to speed up their downloads and connection speeds but don't want to pay more than they are paying right now. They currently pay $200/mo. The main office is in... (4 Replies)
Discussion started by: Jodibaxter
4 Replies
2. IP Networking
i was reading this thread and someone mentioned problems with the linksys 4 portcable/dsl routers, (BEF4somethingsomethingsomething) this is what i use on my network, and works great, BUT i have had a few strange problems, well my question is not too much of a question, but i would like to know... (0 Replies)
Discussion started by: norsk hedensk
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Please help to write DOS /Perl script to capture router AAA logs to store in file.
RADIUS: id 1, priority 1, host 59.163.6.103, auth-port 1901, acct-port 1902
State: current UP, duration 1928071s, previous duration 0s
Dead: total time 2798488914s, count 0
Authen:... (0 Replies)
Discussion started by: patilanna
0 Replies
4. Infrastructure Monitoring
Hi
Can any one please guide me how can I configure a few commands for a few devices in file1.txt.
username: user1
password: pass
enable pass: ep
file1.txt:
device1.abc.com
device2.abc.com
router.xpy.com
I want to apply all the config lines for each device in file1.txt
... (0 Replies)
Discussion started by: sureshcisco
0 Replies
5. Shell Programming and Scripting
Hello All,
I have 10 routers, and need to write a script so that each router pings each other and get the result in a file.
We need to further extract the min/avg/max result and write a script to put in a excel file.
E.g.
LAB-R3A-7609#ping 6.6.6.6
Type escape... (1 Reply)
Discussion started by: sanjugab
1 Replies
6. Shell Programming and Scripting
Hi all,
I use a bash script which use expect to connect throught ssh and run command on a cisco router. The ssh connection with expect work fine, but the first command on the cisco router failed,
I try to run the command in error by hand and it work fine... :(
the first part of the script... (2 Replies)
Discussion started by: bedomon
2 Replies
7. Shell Programming and Scripting
Hi all
i have little problem finding solution about simple telnet script .... i have 250 routers and on some i have different password and on some they ask just for password no username. So for example 1,2,3 have username and password (user,password) 4, and 5 have different username and password... (0 Replies)
Discussion started by: IvanMP
0 Replies
LEARN ABOUT FREEBSD
liebert
LIEBERT(8) NUT Manual LIEBERT(8)
NAME
liebert - Driver for Liebert contact-closure UPS equipment
NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
You may have to build another cable with DTR connected through to the UPS for it to work.
There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
fundamental limitation of any contact-closure driver.
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 LIEBERT(8)