Sponsored Content
Full Discussion: Network settings
Top Forums UNIX for Dummies Questions & Answers Network settings Post 52663 by rhfrommn on Wednesday 23rd of June 2004 10:14:43 AM
Old 06-23-2004
Depends on which version of Unix you are using.

In general your best bet is to try ifconfig. In Solaris ifconfig -a will show you everything. Do a man ifconfig if you are on another version to see which options you need. You can also change network settings on the fly with ifconfig.

If you want to change settings permanently (i.e. so after rebooting it comes up with the new settings) you need to change some config files. Again, since I know Solaris best I can tell you that you'd need to change files like
/etc/hosts
/etc/hostname.hme0
/etc/defaultrouter
/etc/netmasks
or maybe some others depending on exactly what you were trying to do. For different versions of Unix or Linux the filenames might be different.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network settings on Red Hat

HELP!! How do you change the network setting from auto-duplex to 100 Base T Full Duplex in Red HaT? (1 Reply)
Discussion started by: johnlong
1 Replies

2. Linux

Mandriva 2006 keeps resetting network settings...

I've been looking for documentation on how to stop this behavior. I have two nics in my system. eth0: configured manually and as a dhcp server for the local network eth1: configured w/ dhcp enabled connected to router dns server addresses keep getting reset every few minutes. i suspect... (0 Replies)
Discussion started by: rbetzen
0 Replies

3. Solaris

Network settings

I have problem with network settings. Where i can find network config ? I'm newbie, but i very want learn this OS. I find : /etc/hostname.<interface> /etc/netconfig /etc/netmasks /etc/networks /etc/inet/hosts But where i can write my IP-address and after reboot i be know that my server... (2 Replies)
Discussion started by: jess_t03
2 Replies

4. IP Networking

ssh server is attachable from local network not from another network

hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies

5. HP-UX

Network Printer Settings-landscape/portrait mode

Hello everyone.. While printing through command line, we can set printing option with -o <lanscape/portrait> to print file in required mode. But i want to know is there any way we can set this as default behaviour for this printer? After configuration any script we can modify for this... (0 Replies)
Discussion started by: laxmikant
0 Replies

6. UNIX for Dummies Questions & Answers

Linux Server Network Settings - Share Directory Structure

Hello Unix Gurus Who I Hope Reads This, I have quasi-inherited control over a Linux cluster at a university research lab. The post-doc that set it up is gone, and the person in charge of administering the cluster doesn't know a ton about Linux. Amongst other things, I want to use the cluster... (0 Replies)
Discussion started by: mbl
0 Replies

7. Solaris

Creating A Solaris Zone - Unable to install - Are network settings required?

Hi i have created a solaris zone but have not yet connected any network cables for this new zone, can i set the zone up without running the command 'add net' and not adding an ip or physical interface? i tried to add dummy internet settings and get this zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies

8. Shell Programming and Scripting

Script to adjust network settings

Hello, Newbie question on scripting - I'm looking to create a simple script that will work on RHEL5 that will adjust the network settings: ip address, default gateway, and subnet mask. If anything else needs to be done (service network stop / start) or should be done to make settings active - I... (4 Replies)
Discussion started by: rojizo
4 Replies

9. UNIX for Dummies Questions & Answers

Network settings on Motorola System V R32V3.2

Hi, I have inherited a Motorola System V R32V3.2 system. The system works fine, but we need to change the network settings. I've changed the IP address successfully, however I'm lost on the gateway and subnet mask. I've changed the default gateway using route -g10.0.8.1, but it changes back to... (7 Replies)
Discussion started by: Tilmar
7 Replies
IPSEC_SUBNETOF(3)					     Library Functions Manual						 IPSEC_SUBNETOF(3)

NAME
ipsec_subnetof, ipsec_hostof, ipsec_broadcastof - given Internet address and subnet mask return subnet number, host part, broadcast address SYNOPSIS
#include <freeswan.h> struct in_addr subnetof(struct in_addr addr, struct in_addr mask); struct in_addr hostof(struct in_addr addr, struct in_addr mask); struct in_addr broadcastof(struct in_addr addr, struct in_addr mask); DESCRIPTION
These functions are obsolete; see ipsec_networkof(3) for their replacements. Subnetof takes an Internet address and a subnet mask and returns the network part of the address (all in network byte order). Hostof simi- larly returns the host part, and broadcastof returns the broadcast address (all-1s convention) for the network. These functions are provided to hide the Internet bit-munging inside an API, in hopes of easing the eventual transition to IPv6. SEE ALSO
inet(3), ipsec_atosubnet(3) HISTORY
Written for the FreeS/WAN project by Henry Spencer. BUGS
Calling functions for this is more costly than doing it yourself. 11 June 2001 IPSEC_SUBNETOF(3)
All times are GMT -4. The time now is 10:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy