Sponsored Content
Full Discussion: ping -t
Top Forums Shell Programming and Scripting ping -t Post 50141 by Optimus_P on Friday 16th of April 2004 04:17:39 PM
Old 04-16-2004
this is not a script palace. If you need assistance in writeing one then post what you have and we can help nudge you along.

please do not expect complete work to be handed over to you on a whim.
 

10 More Discussions You Might Find Interesting

1. IP Networking

About Ping

Hi, When I pinged a machin, I got to be seen a different kind of reply from that machine. This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message. So what does this mean. Regards & Thanks in advance. Vishwa. (4 Replies)
Discussion started by: S.Vishwanath
4 Replies

2. UNIX for Dummies Questions & Answers

ping

Hi there hope list can help I'm looking for a command that does the following lets say i ping a server 00.00.000.00 and this server is up and running how do i get the ping command to return a UP or a Down meaning if the command is true do this if the command is False do this ... (2 Replies)
Discussion started by: nemex
2 Replies

3. AIX

ping

We can ping out but the return never comes back even to localhost ping localhost PING loopback: (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms it just sits there.... any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies

4. UNIX for Dummies Questions & Answers

Ping

Hi , I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this? sam70 (1 Reply)
Discussion started by: sam70
1 Replies

5. Linux

Not able to ping

Hi All, Need your help one more time. I am trying to ping a linux machine which is not responding to ping. However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0". It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies

6. IP Networking

Can't Ping

I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative. ... (7 Replies)
Discussion started by: Rutgerncas
7 Replies

7. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies

8. IP Networking

PING

I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies

9. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies

10. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
yodlpost(1)						    Your Own Document Language						       yodlpost(1)

NAME
yodlpost - Yodl post-processor SYNOPSIS
yodlpost [options] index yodlout [out] DESCRIPTION
The Yodl post processor is used to solve references into the converted text, and to split (where appropriate) the converted Yodl text in parts. Some conversions do not require post-processing, such as LaTeX, but most do. Therefore, in most cases a Yodl conversion consists of two phases: o First, yodl(1) is called, producing a raw output file and an associated index file; o Then, yodlpost(1) is called, converting these two files into a final document. Normally, yodl2...(1) scripts are used to perform complete Yodl conversions. OPTIONS
-x ext: extension of the out-s if different from out's extension itself. If omitted, and out has no extension, ypp (Yodl Post Processor) is used. SEE ALSO
yodlstriproff(1), yodl(1), yodlbuiltins(7), yodlconverters(1), yodlletter(7), yodlmacros(7), yodlmanpage(7), yodlverbinsert(1). BUGS
- AUTHOR
Frank B. Brokken (f.b.brokken@rug.nl), yodl_3.00.0.tar.gz 1996-2010 yodlpost(1)
All times are GMT -4. The time now is 03:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy