08-01-2001
? Configuring a Quad-Port card ?
I am running Solaris 2.6 on a Sparc 10. I just installed my Quad-card and I am able to assign IP addresses to each port and PING out. I have created the "hostname.qe0 - hostname.qe3" files and added the appropriate IP address of each port to each file. When I reboot, none of the settings stay. I have to manually add the IP addresses to each port again. The integrated NIC's setting are fine (le0). When the system is loading it replies with:
Interface
qe0 - Link state down
qe1 - Link state down
qe2 - Link state down
qe3 - Link state down
This is the command I use to configure the Ip addresses:
ifconfig qe0 10.10.10.6 up
Why aren't the IP addresses being saved?
Last edited by jskillet; 08-01-2001 at 03:54 PM..
9 More Discussions You Might Find Interesting
1. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
2. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
3. UNIX for Dummies Questions & Answers
hi all,
i've got an old PC with unix (SCO System V/386 rel. 3.2) on it.
Pentium I; 128mb; ISA 2-port RS232 serial adapter card for an oki dot-matrix printer. (no usb, no CD)
i've been running an old cobol program to do some invoicing and print reports.
some time back i changed the... (0 Replies)
Discussion started by: frankpky
0 Replies
4. SCO
hello everybody,
i am a new user for sco OS , i want to know how i can configure a graphical card under this system.
and usb DAT plzzz (0 Replies)
Discussion started by: lid-j-one
0 Replies
5. UNIX Desktop Questions & Answers
Does Red Hat Fedora support Nvidia card 8800GTX and 260 card?
Does any Linux OS support Nvidia card? (1 Reply)
Discussion started by: sito
1 Replies
6. UNIX for Dummies Questions & Answers
I want to connect to the internet via Wi-Fi, but I need to configure my pci adapter card for it to work. The adapter I am using is a Linksys Wireless-G pci adapter wmp54gs.:confused: (5 Replies)
Discussion started by: ryan352333
5 Replies
7. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
8. Shell Programming and Scripting
hi I juts want to know if there is a command that checks if an ethernet port corresponds to a network card.
ex. I have 3 network cards, one is two ports, and the other two 8 ports.
How do I know that eth0 corresponds to the the two-port network card and eth9 corresponds to the first 8-port... (2 Replies)
Discussion started by: h0ujun
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT OPENDARWIN
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD