|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Installing Linux on an individual drive and the MBR..
Post 4808 by Neo on Wednesday 1st of August 2001 12:22:15 AM
08-01-2001
Administrator
You will still need to install lilo and make sure your MBR is correct.
The root, var, home, etc directories are all normally part of the / partition. This can easily be less than 500 MB on a 30 GB drive!
The rest of the drive can be a nice /usr partition of about 5 GB and
the rest on /usr/local ....... (don't forget to add a swap partition, at least the size of your RAM, some people go 2XRAM for swap, but that was in the old days when RAM was rare and expensive. Now, with 128 MB and 256 MB RAM common, swap is rarely needed).
Of course, there are other ways to do this....
The root, var, home, etc directories are all normally part of the / partition. This can easily be less than 500 MB on a 30 GB drive!
The rest of the drive can be a nice /usr partition of about 5 GB and
the rest on /usr/local ....... (don't forget to add a swap partition, at least the size of your RAM, some people go 2XRAM for swap, but that was in the old days when RAM was rare and expensive. Now, with 128 MB and 256 MB RAM common, swap is rarely needed).
Of course, there are other ways to do this....
|
|
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
2. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
3. Red Hat
Hi ,
I have two disk installed with Linux(disk 1) and WinXP(disk 2) .Now i am changing Hardisk jumbper manualy to get in to Linux/Windows .I want to configure my REDHAT linux boot manager to list Linux and WindowXP and wanna boot according to my choice .
Here is what my fdisk -l shows (Only... (2 Replies)
Discussion started by: gkrishn
2 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. UNIX for Dummies Questions & Answers
Hi,
i installed a unix tape drive on my alphaserver. when i use a mt command it tells me there is no tape or device.
I have used the hardware manager and it shows the tape is present.
Can anyone help me understand why it cannot pick up the tape as a default? (1 Reply)
Discussion started by: ryks
1 Replies
6. UNIX for Dummies Questions & Answers
Where can I find instructions for doing this? I am running Win XP and would like to be able to run solaris 10 from my flash drive.
Thanks,
Carrie (3 Replies)
Discussion started by: Carrie Heiser
3 Replies
7. UNIX for Dummies Questions & Answers
Hello
I have a new project being kicked off next month and i should learn UNIX fast. I have never used UNIX before so i have the following questions:
1) Is any UNIX free to install?
2) Can i install and boot UNIX from an External Hard Drive (The system board on my laptop crashed so i took the... (2 Replies)
Discussion started by: pipsonian
2 Replies
8. Red Hat
How should i install Fedora onto flash drive .. to boot the OS from flash drive..
plz help me in that!! :( (4 Replies)
Discussion started by: dude_me5
4 Replies
9. Windows & DOS: Issues & Discussions
Hello,
My hard drive was formatted with GPT. It is part of a volume group and has two logical volumes on it. Is it possible to convert the drive to MBR? If so, how would I got about doing it? I know there are programs out there that do it, but I have volume groups with LVM's so I am wondering if... (1 Reply)
Discussion started by: mojoman
1 Replies
LEARN ABOUT DEBIAN
dtc_setup_vps_disk
dtc_setup_vps_disks(8) System Manager's Manual dtc_setup_vps_disks(8) NAME
dtc_setup_disk - setup LVM disks for using it as a VM SYNOPSIS
dtc_setup_vps_disk.sh VPS_NUMBER HDD_SIZE SWAP_SIZE [ lvm|loopback ] DESCRIPTION
dtc_setup_vps_disk.sh This shell script is a part of the dtc-xen package that is to be used by the dtc panel to manage a Xen VPS server. This script is used to create partitions to be used by a VPS later on. It will create a normal partition that will be used as a root disk, and a swap partition. dtc_setup_disk is to be used by the dtc-xen SOAP server, but can also be used as a standalone userland tool. If the partition(s) exists, then this script will delete it/them first. OPTIONS
VPS_NUMBER has to be a number between 01 and 19. Let's say the number is 16, and that dtc-xen is configured to use the volume group called lvm1, then this script will create /dev/lvm1/xen16 and /dev/lvm1/xen16swap. HDD_SIZE Size in MB of the VPS partition to create. SWAP_SIZE Size in MB of the VPS swap partition to create. If the dtc-xen SOAP server is used to create the VPS, then it will create a swap partition of the exact same size as the memory. IMAGE_TYPE This parameter can have 2 values: either lvm or loopback. If ommited, then lvm is used. If lvm is used, then this script will create a partition using lvmcreate, otherwise it will create an image file. Both will later be used for the VPS. EXAMPLE
dtc_setup_vps_disk 04 15360 256 lvm This will create 2 LVM partition to be used by the VPS named xen04, the first one being a root partition of 15 GB, and the second one being a swap partition of 256 MB. VERSION
This documentation describes dtc_setup_vps_disk version 0.3.15. See http://www.gplhost.com/software-dtc-xen.html for updates. SEE ALSO
dtc_reinstall_os(8), dtc_kill_vps_disk(8) dtc_setup_vps_disks(8)