Sponsored Content
Full Discussion: bus error on solaris
Top Forums UNIX for Dummies Questions & Answers bus error on solaris Post 46929 by jsilva on Thursday 29th of January 2004 09:31:34 AM
Old 01-29-2004
Hi,

There're many reasons for a "bus error". It may be because the program ( top ) is trying to do some I/O operation to a device that has no permissions or does not exist... confirm that that only happens with top... is there any core dump ? It can be caused by bad programming too... or some OS issue...
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Bus Error

This may belong in the C Programming forum, but here goes anyway... What would cause a bus error? I searched google for a cause, but came up with some conflicting reports... Could it be caused by disk space? A lot of the pages I found mentioned linking with the incorrect versions of the... (4 Replies)
Discussion started by: LivinFree
4 Replies

2. UNIX for Dummies Questions & Answers

Bus error(coredump

aix 5.3 ML1 system was functioing well, when suddenly telnet session hung and then I got the following message "Bus error(coredump)" would appreciate if anyone would assist as to what to do next. (3 Replies)
Discussion started by: Student37
3 Replies

3. UNIX for Advanced & Expert Users

Bus Error(coredump)

Hi, I am using HP-UX. While i try to run the Sqlplus command using the shel script in encounter the following error: <shell script name>: some number Bus Error(coredump) What may be the reason behind this. I read few previous threads in this forum where i found some similar case. There it was... (2 Replies)
Discussion started by: Jayesh
2 Replies

4. Programming

BUS error

Hi! I've got a program which runs fine under Linux, but I have compiled it to run under SunOS 5.8 in a Sparc computer, and now it sometimes fails with "bus error". Ussing gdb I surfed to the error line, which is *pointer = some_vector; where some_vector is a 16 byte struct (4 integers)... (1 Reply)
Discussion started by: shesatmine
1 Replies

5. UNIX for Dummies Questions & Answers

bus error (coredump)

Hi all, I am getting bus error problem in SunOS. Can you please help me out in this regard. Actually, my entire code till the last line has been executed. But after tht i am getting a bus error. Please help me. Thanks in advance. Charu. (4 Replies)
Discussion started by: charu
4 Replies

6. HP-UX

Need help on Bus error(coredump)

Hi all, I am quite weak in C but I need to get some work done. Hope someone can help me out. I keep getting this error when i try to run my C application in my HP-UX 10.20 machine. Some code snippet: Month(DBTime) =====This is a function which will return variable "CutOffTime" to be use... (5 Replies)
Discussion started by: Vision©
5 Replies

7. HP-UX

Bus Error

I am getting bus error when i include "#!/bin/ksh". If i remove interpreter then script is working. Can anyone explain this and how can i avoid this error? Operating System is HP-UX B.11.23 U 9000/800 1091834454 (2 Replies)
Discussion started by: anbu23
2 Replies

8. Programming

Bus error

Hi everyone, I have a GUI project and when I run it and left in idle state for a long time(there is nothing done, just opened GUI, no more actions),I get bus error after trying to do anything with it. I've tried to build it in debug mode and use gdb, but I don't get any error in debug mode.It... (3 Replies)
Discussion started by: sisi
3 Replies

9. Programming

Bus Error: 10...Help please!

Hi all, I am writing a phonebook program to store names and number using a list. Here is the code for the function which allows the user to enter the name and number (where the error occurs). //THIS FUNCTION ADDS A NEW ENTRY TO THE phonebook_list void insert(void){ //variables int... (5 Replies)
Discussion started by: kdejan
5 Replies

10. Programming

Solaris - BUS error with optimize mode

Hi, I'm facing BUS (invalid address alignment) issue. Application works correctly with binaries compiled without optimization. When "-O3" (or -O2, O1) is in use, application abort with - BUS (invalid address alignment). The problem appears in following situation: struct _a { int... (15 Replies)
Discussion started by: revolta25
15 Replies
DEVICE(9)						   BSD Kernel Developer's Manual						 DEVICE(9)

NAME
device -- an abstract representation of a device SYNOPSIS
typedef struct device *device_t; DESCRIPTION
The device object represents a piece of hardware attached to the system such as an expansion card, the bus which that card is plugged into, disk drives attached to the expansion card etc. The system defines one device, root_bus and all other devices are created dynamically during autoconfiguration. Normally devices representing top-level busses in the system (ISA, PCI etc.) will be attached directly to root_bus and other devices will be added as children of their relevant bus. The devices in a system form a tree. All devices except root_bus have a parent (see device_get_parent(9)). In addition, any device can have children attached to it (see device_add_child(9), device_add_child_ordered(9), device_find_child(9), device_get_children(9), and device_delete_child(9)). A device which has been successfully probed and attached to the system will also have a driver (see device_get_driver(9) and driver(9)) and a devclass (see device_get_devclass(9) and devclass(9)). Various other attributes of the device include a unit number (see device_get_unit(9)), verbose description (normally supplied by the driver, see device_set_desc(9) and device_get_desc(9)), a set of bus-spe- cific variables (see device_get_ivars(9)) and a set of driver-specific variables (see device_get_softc(9)). Devices can be in one of several states: DS_NOTPRESENT the device has not been probed for existence or the probe failed DS_ALIVE the device probe succeeded but not yet attached DS_ATTACHED the device has been successfully attached DS_BUSY the device is currently open The current state of the device can be determined by calling device_get_state(9). SEE ALSO
devclass(9), driver(9) AUTHORS
This manual page was written by Doug Rabson. BSD
June 16, 1998 BSD
All times are GMT -4. The time now is 11:04 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy