|
|
Sponsored Content
UNIX Standards and Benchmarks
UNIX & LINUX Benchmarks (Version 3.11)
UNIX Benchmarks
1024 Mb RAM / 648MHz Sparc Processor
Post 46804 by mattd on Monday 26th of January 2004 10:59:32 PM
01-26-2004
1024 Mb RAM / 648MHz Sparc Processor
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS as-1 5.8 Generic_108528-24 sun4u sparc SUNW,UltraAX-i2
Start Benchmark Run: Tue Jan 27 15:07:18 NZDT 2004
3 interactive users.
Dhrystone 2 without register variables 839082.6 lps (10 secs, 6 samples)
Dhrystone 2 using register variables 768424.1 lps (10 secs, 6 samples)
Arithmetic Test (type = arithoh) 3831540.9 lps (10 secs, 6 samples)
Arithmetic Test (type = register) 53315.1 lps (10 secs, 6 samples)
Arithmetic Test (type = short) 52631.3 lps (10 secs, 6 samples)
Arithmetic Test (type = int) 54740.7 lps (10 secs, 6 samples)
Arithmetic Test (type = long) 50915.0 lps (10 secs, 6 samples)
Arithmetic Test (type = float) 151544.7 lps (10 secs, 6 samples)
Arithmetic Test (type = double) 110019.7 lps (10 secs, 6 samples)
System Call Overhead Test 121167.1 lps (10 secs, 6 samples)
Pipe Throughput Test 71138.2 lps (10 secs, 6 samples)
Pipe-based Context Switching Test 39083.3 lps (10 secs, 6 samples)
Process Creation Test 419.8 lps (10 secs, 6 samples)
Execl Throughput Test 230.7 lps (9 secs, 6 samples)
File Read (10 seconds) 448931.0 KBps (10 secs, 6 samples)
File Write (10 seconds) 58897.0 KBps (10 secs, 6 samples)
File Copy (10 seconds) 29088.0 KBps (10 secs, 6 samples)
File Read (30 seconds) 424893.0 KBps (30 secs, 6 samples)
File Write (30 seconds) 63927.0 KBps (30 secs, 6 samples)
File Copy (30 seconds) 19336.0 KBps (30 secs, 6 samples)
C Compiler Test 22990.0 lpm (60 secs, 3 samples)
Shell scripts (1 concurrent) 314.1 lpm (60 secs, 3 samples)
Shell scripts (2 concurrent) 159.0 lpm (60 secs, 3 samples)
Shell scripts (4 concurrent) 84.6 lpm (60 secs, 3 samples)
Shell scripts (8 concurrent) 42.3 lpm (60 secs, 3 samples)
Dc: sqrt(2) to 99 decimal places 6299.2 lpm (60 secs, 6 samples)
Recursion Test--Tower of Hanoi 16921.3 lps (10 secs, 6 samples)
INDEX VALUES
TEST BASELINE RESULT INDEX
Arithmetic Test (type = double) 2541.7 110019.7 43.3
Dhrystone 2 without register variables 22366.3 839082.6 37.5
Execl Throughput Test 16.5 230.7 14.0
File Copy (30 seconds) 179.0 19336.0 108.0
Pipe-based Context Switching Test 1318.5 39083.3 29.6
Shell scripts (8 concurrent) 4.0 42.3 10.6
=========
SUM of 6 items 243.0
AVERAGE 40.5
So is this good/bad or indifferent?
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS as-1 5.8 Generic_108528-24 sun4u sparc SUNW,UltraAX-i2
Start Benchmark Run: Tue Jan 27 15:07:18 NZDT 2004
3 interactive users.
Dhrystone 2 without register variables 839082.6 lps (10 secs, 6 samples)
Dhrystone 2 using register variables 768424.1 lps (10 secs, 6 samples)
Arithmetic Test (type = arithoh) 3831540.9 lps (10 secs, 6 samples)
Arithmetic Test (type = register) 53315.1 lps (10 secs, 6 samples)
Arithmetic Test (type = short) 52631.3 lps (10 secs, 6 samples)
Arithmetic Test (type = int) 54740.7 lps (10 secs, 6 samples)
Arithmetic Test (type = long) 50915.0 lps (10 secs, 6 samples)
Arithmetic Test (type = float) 151544.7 lps (10 secs, 6 samples)
Arithmetic Test (type = double) 110019.7 lps (10 secs, 6 samples)
System Call Overhead Test 121167.1 lps (10 secs, 6 samples)
Pipe Throughput Test 71138.2 lps (10 secs, 6 samples)
Pipe-based Context Switching Test 39083.3 lps (10 secs, 6 samples)
Process Creation Test 419.8 lps (10 secs, 6 samples)
Execl Throughput Test 230.7 lps (9 secs, 6 samples)
File Read (10 seconds) 448931.0 KBps (10 secs, 6 samples)
File Write (10 seconds) 58897.0 KBps (10 secs, 6 samples)
File Copy (10 seconds) 29088.0 KBps (10 secs, 6 samples)
File Read (30 seconds) 424893.0 KBps (30 secs, 6 samples)
File Write (30 seconds) 63927.0 KBps (30 secs, 6 samples)
File Copy (30 seconds) 19336.0 KBps (30 secs, 6 samples)
C Compiler Test 22990.0 lpm (60 secs, 3 samples)
Shell scripts (1 concurrent) 314.1 lpm (60 secs, 3 samples)
Shell scripts (2 concurrent) 159.0 lpm (60 secs, 3 samples)
Shell scripts (4 concurrent) 84.6 lpm (60 secs, 3 samples)
Shell scripts (8 concurrent) 42.3 lpm (60 secs, 3 samples)
Dc: sqrt(2) to 99 decimal places 6299.2 lpm (60 secs, 6 samples)
Recursion Test--Tower of Hanoi 16921.3 lps (10 secs, 6 samples)
INDEX VALUES
TEST BASELINE RESULT INDEX
Arithmetic Test (type = double) 2541.7 110019.7 43.3
Dhrystone 2 without register variables 22366.3 839082.6 37.5
Execl Throughput Test 16.5 230.7 14.0
File Copy (30 seconds) 179.0 19336.0 108.0
Pipe-based Context Switching Test 1318.5 39083.3 29.6
Shell scripts (8 concurrent) 4.0 42.3 10.6
=========
SUM of 6 items 243.0
AVERAGE 40.5
So is this good/bad or indifferent?
|
|
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i recently purchased a dual ross sparc processor kit from someone.
the person listed these items as 133mhz processors, however, looking at bridgepoint's site, they do not make 133mhz processors.
so i was wondering, how can i check the processor speeds? (4 Replies)
Discussion started by: xyyz
4 Replies
2. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
3. UNIX for Advanced & Expert Users
Hi guys,
Just needed to know if all the ports above 1024 are closed by default. I know that below 1024 the ports are reserved for the kernel and ports above 1024 are reserved for user applications.
But by default, if I do not have a rule in my firewall to block ports above 1024, Will my... (4 Replies)
Discussion started by: firefox211
4 Replies
4. Red Hat
Hi,
On server 64bit Hw Arch , Linux 5.0(32bit) is installed it is showing only 3gb of ram though physical is 16gb
can u give me idea why? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. Linux Benchmarks
CPU/Speed: AMD Phenom(tm) 9950 Quad-Core Processor
Ram: 3.6 GB
Motherboard: Foxconn 7da-s
Bus:
Cache:
Controller:
Disk:
Load:
Kernel: Linux 2.6.26-2-amd64
Kernel ELF?:
pgms:
==============================================================
BYTE UNIX Benchmarks (Version... (0 Replies)
Discussion started by: migracho
0 Replies
6. Red Hat
Hi All,
How do I know if ssh_host_rsa_key is 1024 bit?
cat /etc/ssh/ssh_host_rsa_key | wc -m
887
It's only 887. Is that it? Or not?
Thank you for any comment you may add. (2 Replies)
Discussion started by: itik
2 Replies
7. UNIX for Dummies Questions & Answers
How to generate RSA 1024 public key??
Pls help (3 Replies)
Discussion started by: kdtrica
3 Replies
8. Shell Programming and Scripting
Hi i have a txt file in which i do a awk operation with ":" as field separator
A
B
C
D
ABC::2386.13:2386.13:3248234281995::+DPY:INT:3:N::::2:200.00:0.00:2010-05-12:CA:
::2:N::N:PH:00010031:0001+DPY:BAL:3:N::::3:1601.01:0.00:2010-05-12:XT::2:N:MR ... (1 Reply)
Discussion started by: mad_man12
1 Replies
LEARN ABOUT MINIX
volcheck
volcheck(1) User Commands volcheck(1) NAME
volcheck - checks for media in a drive and by default checks all floppy media SYNOPSIS
volcheck [-v] [-i secs] [-t secs] pathname DESCRIPTION
The volcheck utility tells Volume Management to look at each dev/pathname in sequence and determine if new media has been inserted in the drive. The default action is to volcheck all checkable media managed by volume management. OPTIONS
The following options are supported: -i secs Set the frequency of device checking to secs seconds. The default is 2 seconds. The minimum frequency is 1 second. -t secs Check the named device(s) for the next secs seconds. The maximum number of seconds allowed is 28800, which is 8 hours. The fre- quency of checking is specified by -i. There is no default total time. -v Verbose. OPERANDS
The following operands are supported: pathname The path name of a media device. EXAMPLES
Example 1: A sample of the volcheck command. The following example example% volcheck -v /dev/diskette /dev/diskette has media asks Volume Management to examine the floppy drive for new media. The following example example% volcheck -i 2 -t 600 /dev/diskette1 & asks Volume Management if there is a floppy in the floppy drive every 2 seconds for 600 seconds (10 minutes). FILES
/dev/volctl Volume Management control port ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWvolu | +-----------------------------+-----------------------------+ SEE ALSO
eject(1), volcancel(1), volmissing(1) rmmount(1M), vold(1M), rmmount.conf(4), vold.conf(4), attributes(5), volfs(7FS) WARNINGS
Due to a hardware limitation in many floppy drives, the act of checking for media causes mechanical action in the floppy drive. Continu- ous polling of the floppy drive will cause the drive to wear out. It is recommended that polling the drive only be performed during periods of high use. SunOS 5.10 21 Feb 1997 volcheck(1)