11-19-2003
One more thing....
Am I correct in thinking that Adaptec cards are verboten in this machine? If they aren't, that may be the cheaper/easier route.
Thanks.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
2. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
3. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
4. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
5. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
6. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
7. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
8. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
9. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
LEARN ABOUT FREEBSD
aacraid
AACRAID(4) BSD Kernel Interfaces Manual AACRAID(4)
NAME
aacraid -- Adaptec AACRAID Controller driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device aacraid
To compile in debugging code:
options AACRAID_DEBUG=N
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
aacraid_load="YES"
DESCRIPTION
The aacraid driver provides support for the Adaptec by PMC RAID controllers, including Series 6/7/8 and upcoming families.
The RAID containers are handled via the aacraidp0 bus. The physical buses are represented by the aacraidp? devices (beginning with
aacraidp1). These devices enable the SCSI pass-thru interface and allows devices connected to the card such as CD-ROMs to be available via
the CAM scsi(4) subsystem. Note that not all cards allow this interface to be enabled.
The /dev/aacraid? device nodes provide access to the management interface of the controller. One node exists per installed card. If the
kernel is compiled with the COMPAT_LINUX option, or the aacraid_linux.ko and linux.ko modules are loaded, the Linux-compatible ioctl(2)
interface for the management device will be enabled and will allow Linux-based management applications to control the card.
HARDWARE
Controllers supported by the aacraid driver include:
o Adaptec ASR-6405(T|E)
o Adaptec ASR-6445
o Adaptec ASR-6805(T|E|Q|TQ)
o Adaptec ASR-7085
o Adaptec ASR-7805(Q)
o Adaptec ASR-70165
o Adaptec ASR-71605(E|Q)
o Adaptec ASR-71685
o Adaptec ASR-72405
o Adaptec Series 8 cards
FILES
/dev/aacraid? aacraid management interface
DIAGNOSTICS
Compiling with AACRAID_DEBUG set to a number between 0 and 3 will enable increasingly verbose debug messages.
The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console, and are also
queued for retrieval by a management application.
SEE ALSO
kld(4), linux(4), scsi(4), kldload(8)
AUTHORS
Achim Leubner <achim@FreeBSD.org>
Ed Maste <emaste@FreeBSD.org>
Scott Long <scottl@FreeBSD.org>
BUGS
The controller is not actually paused on suspend/resume.
BSD
April 09, 2013 BSD