11-10-2003
hi
thanx, by the way, what the rule for find out the network address and broadcast address, if in this case, the IP address is class A, is it the 10.0.0.0 for network address, and 10.0.0.255 for broadcast address? what is the rule for that?
Thanx for help
10 More Discussions You Might Find Interesting
1. IP Networking
What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies
2. Solaris
I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (1 Reply)
Discussion started by: csaunders
1 Replies
3. AIX
Hi, I try to understand how to configure my ethernet network in a hacmp cluster.
I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster.
I don't have any serial o iscsi heartbeat.
Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies
4. Shell Programming and Scripting
Hi
Suppose
You have two computers. One named kenny which has an IP address of 192.168.0.7. kenny lives
on a subnet with a subnet mask of 255.255.255.240. The second computer is called zathras, which
has an IP address of 192.168.0.17, zathras lives on a network with the same subnet mask.
i)... (4 Replies)
Discussion started by: scofiled83
4 Replies
5. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
6. UNIX for Dummies Questions & Answers
:) Firstly Hi all!!, im NEW!! and on here hoping that someone might be able to offer me some help... i have a server that keeps crashing every few days with the error message:
PANIC KERNAL-MODE ADDRESS FAULT ON USER ADDRESS 0X14
KERNAL PAGE FAULT FROM (CS:EIP)=(100:EF71B5BD)
EAX=EF822000... (10 Replies)
Discussion started by: Twix
10 Replies
7. UNIX for Dummies Questions & Answers
Good morning!
Why would having a fake network device be useful?
Thanks in advance
Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies
8. Shell Programming and Scripting
Hello,
I am running a post script in autoyast where I am trying to set the broadcast and network address.
I have the ip address and netmask already (reading from a file)..
I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast.
Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies
9. IP Networking
How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died.
I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT DEBIAN
wakeonlan
WAKEONLAN(1) User Contributed Perl Documentation WAKEONLAN(1)
NAME
wakeonlan - Perl script to wake up computers
SYNOPSIS
wakeonlan [-h] [-v] [-i IP_address] [-p port] [-f file] [[hardware_address] ...]
DESCRIPTION
This script sends 'magic packets' to wake-on-lan enabled ethernet adapters and motherboards, in order to switch on the called PC. Be sure
to connect the NIC with the motherboard if neccesary, and enable the WOL function in the BIOS.
The 'magic packet' consists of 6 times 0xFF followed by 16 times the hardware address of the NIC. This sequence can be encapsulated in any
kind of packet. This script uses UDP packets.
OPTIONS
-h Displays the help information.
-v Displays the script version.
-i ip_address
Destination IP address. Unless you have static ARP tables you should use some kind of broadcast address (the broadcast address of the
network where the computer resides or the limited broadcast address). Default: 255.255.255.255 (the limited broadcast address).
-p port
Destination port. Default: 9 (the discard port).
-f file
File with hardware addresses of wakeable computers. For an example check the file lab001.wol in the examples subdirectory.
EXAMPLES
Using the limited broadcast address (255.255.255.255):
$ wakeonlan 01:02:03:04:05:06
$ wakeonlan 01:02:03:04:05:06 01:02:03:04:05:07
Using a subnet broadcast address:
$ wakeonlan -i 192.168.1.255 01:02:03:04:05:06
Using another destination port:
$ wakeonlan -i 192.168.1.255 -p 1234 01:02:03:04:05:06
Using a file as source of hardware and IP addresses:
$ wakeonlan -f examples/lab001.wol
$ wakeonlan -f examples/lab001.wol 01:02:03:04:05:06
AUTHOR
Jose Pedro Oliveira <jpo@di.uminho.pt> maintaining and expanding original work done by Ico Doornekamp <ico@edd.dhs.org>.
COPYRIGHT
Copyright (c) 2000-2005 Jose Pedro Oliveira.
This is free software. You may modify it and distribute it under Perl's Artistic Licence. Modified versions must be clearly indicated.
SEE ALSO
For more information regarding this script and Wakeonlan technology just check the following address
http://gsd.di.uminho.pt/jpo/software/wakeonlan/.
perl v5.14.2 2012-03-10 WAKEONLAN(1)