Configure New LTO-2 Tape Drive Post: 42115

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

How to configure tape drive on SUN

I am trying to configure DAT Tape drive on SUN E220 system but I don't have SUN keyboard. I am using a tty terminal k/b. What are my alternavtives? Is there any way to send interupts to the system on OK prompt using tty kb for probe SCSI. Thanks in advance.

2. UNIX for Dummies Questions & Answers

tape drive

Hi, I need to restore my tape backup, when I type "tape status" it gives; status : ready beginning-of-tape write-protected soft errors : 0 hard errors : 0 underruns : 3 but...

3. AIX

AIX 5.3 and PV110T LTO tape Drivers?

Hey anyone have the hot news on where to find out if This tape will work with my AIX 5.3? a Dell PV110T ~ AIX Base Unit: PV110T,LTO-3,400/800GB,EXT PowerVault 110T, LTO-3 400/800GB, External Drive-R (222-2100) Hard Drive Controller: External 4M SCSI Cable VHDCI/68 pin for Tape...

4. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

5. Solaris

configure tape drive to sun solaris 10

Hi everyone. Im new to Sun Solaris or the Unix environment. My only background is the DOS command in windows and a little bit of c++ programming. I always worked with troubleshooting hardware and software issues with windows. Now that I need to configure tape drives using sun solaris, I had...

6. AIX

p570 seeing LTO drive but not 3582 library (smc0)

I have a p570 running AIX 5.2 ml 10. We just got in a IBM 3582 library. The library is connected directly to the lpar via fibre cable. I've installed: Atape.driver 11.7.7.0 atldd.driver 6.8.4.0 After a reboot, I can see the one tape drive: ...

7. Solaris

Sun E220R + HP (SCSI) LTO Ultrium Tape Drive

Hi all, this time I'd need a help from an advanced Solaris system admin :rolleyes: I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all). Now the operating system boot process...

8. HP-UX

TAPE drive

I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help? Thanks in advance

LEARN ABOUT CENTOS

tapset::scsi

tapset::scsi(3stap)													       tapset::scsi(3stap)

NAME

       tapset::scsi - systemtap scsi tapset

DESCRIPTION

	This family of probe points is used to probe SCSI activities.

       scsi.ioentry
	      Prepares a SCSI mid-layer request

	       See probe::scsi.ioentry(3stap)
	       for details.

       scsi.iodispatching
	      SCSI mid-layer dispatched low-level SCSI command

	       See probe::scsi.iodispatching(3stap)
	       for details.

       scsi.iodone
	      SCSI command completed by low level driver and enqueued into the done queue.

	       See probe::scsi.iodone(3stap)
	       for details.

       scsi.iocompleted
	      SCSI mid-layer running the completion processing for block device I/O requests

	       See probe::scsi.iocompleted(3stap)
	       for details.

       scsi.ioexecute
	      Create mid-layer SCSI request and wait for the result

	       See probe::scsi.ioexecute(3stap)
	       for details.

       scsi.set_state
	      Order SCSI device state change

	       See probe::scsi.set_state(3stap)
	       for details.

SEE ALSO

	  probe::scsi.ioentry(3stap),	   probe::scsi.iodispatching(3stap),	  probe::scsi.iodone(3stap),	 probe::scsi.iocompleted(3stap),
       probe::scsi.ioexecute(3stap),  probe::scsi.set_state(3stap),  stap(1), stapprobes(3stap)

IBM
									---						       tapset::scsi(3stap)