Sun Ultra30, Gentoo 1.4.3.10p1 Post: 41443

Sponsored Content

UNIX Standards and Benchmarks UNIX & LINUX Benchmarks (Version 3.11) Linux Benchmarks Sun Ultra30, Gentoo 1.4.3.10p1 Post 41443 by tnorth on Monday 6th of October 2003 12:14:31 PM

10-06-2003

Registered User

Sun Ultra30, Gentoo 1.4.3.10p1

Notes:

Code:

CPU/Speed: UltraSparcII 296Mhz
Ram:512M
Motherboard:
Bus:
Cache:
Controller:
Disk: SEAGATE Model: ST34371W SUN4.2G
Load:
Kernel:
Kernel ELF?:
pgms:

Results:


  BYTE UNIX Benchmarks (Version 3.11)
  System -- Linux box  2.4.21-sparc-r1 #1 Wed Oct 1 12:32:52 EDT 2003 sparc64 sun4u TI UltraSparc II (BlackBird) GNU/Linux
  Start Benchmark Run: Mon Oct  6 10:35:11 EDT 2003
   1 interactive users.
Dhrystone 2 without register variables   576386.0 lps   (10 secs, 6 samples)
Dhrystone 2 using register variables     579571.7 lps   (10 secs, 6 samples)
Arithmetic Test (type = arithoh)         2328097.3 lps   (10 secs, 6 samples)
Arithmetic Test (type = register)         31883.2 lps   (10 secs, 6 samples)
Arithmetic Test (type = short)            30893.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = int)              31726.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = long)             31917.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = float)            91624.5 lps   (10 secs, 6 samples)
Arithmetic Test (type = double)           71655.4 lps   (10 secs, 6 samples)
System Call Overhead Test                122951.4 lps   (10 secs, 6 samples)
Pipe Throughput Test                     103068.5 lps   (10 secs, 6 samples)
Pipe-based Context Switching Test         41634.4 lps   (10 secs, 6 samples)
Process Creation Test                      1922.9 lps   (10 secs, 6 samples)
Execl Throughput Test                       537.8 lps   (9 secs, 6 samples)
File Read  (10 seconds)                  480789.0 KBps  (10 secs, 6 samples)
File Write (10 seconds)                  122483.0 KBps  (10 secs, 6 samples)
File Copy  (10 seconds)                   35198.0 KBps  (10 secs, 6 samples)
File Read  (30 seconds)                  483378.0 KBps  (30 secs, 6 samples)
File Write (30 seconds)                  113817.0 KBps  (30 secs, 6 samples)
File Copy  (30 seconds)                   17388.0 KBps  (30 secs, 6 samples)
C Compiler Test                             183.3 lpm   (60 secs, 3 samples)
Shell scripts (1 concurrent)                958.2 lpm   (60 secs, 3 samples)
Shell scripts (2 concurrent)                507.8 lpm   (60 secs, 3 samples)
Shell scripts (4 concurrent)                261.7 lpm   (60 secs, 3 samples)
Shell scripts (8 concurrent)                132.0 lpm   (60 secs, 3 samples)
Dc: sqrt(2) to 99 decimal places          25150.8 lpm   (60 secs, 6 samples)
Recursion Test--Tower of Hanoi            10871.8 lps   (10 secs, 6 samples)


                     INDEX VALUES
TEST                                        BASELINE     RESULT      INDEX

Arithmetic Test (type = double)               2541.7    71655.4       28.2
Dhrystone 2 without register variables       22366.3   576386.0       25.8
Execl Throughput Test                           16.5      537.8       32.6
File Copy  (30 seconds)                        179.0    17388.0       97.1
Pipe-based Context Switching Test             1318.5    41634.4       31.6
Shell scripts (8 concurrent)                     4.0      132.0       33.0
                                                                 =========
     SUM of  6 items                                                 248.3
     AVERAGE                                                          41.4

tnorth

View Public Profile for tnorth

Find all posts by tnorth

4 More Discussions You Might Find Interesting

1. Linux Benchmarks

AMD 1.2 Gentoo 1.4.3.8p1

Notes: CPU/Speed: 1195.993 Ram: 503 Megabytes Motherboard: biostart m7vkb Bus: Cache:256 KB Controller:VT82C586A Disk:Maxtor 93073U6 Load: Kernel:2.4.20-xfs-r3 Kernel ELF?: yes pgms: Results: BYTE UNIX Benchmarks (Version 3.11) System -- Linux box 2.4.20-xfs-r3 #1...

2. Gentoo

Gentoo problem, X is not working

I got Gentoo installed with only a few minor problems, but those are the worse right? :p Anyway, I can boot into a terminal and could could fine into TWM (yuck). So I emerged XFCE4 by doing this: use="-gnome -kde" emerge xfce I then inserted this into ~./xinitrc : ...

3. Gentoo

Gentoo and Qmail

Hello all, I want to create a qmail to just forward messages to a valid smtp over the internet, so I can use mutt to send messages as well as recieving them. Is there an easy way of doing this? My SMTP server requires authentication. Thanks a lot.

4. UNIX for Advanced & Expert Users

Installing oracle on Gentoo

Hello! I'm using Linux Gentoo 2.6.22-gentoo-r9. Before I used Red Had I had no issues with the installation. But I don't like Red Hat and trying to install Oracle on Gentoo. See following: rpm --nodeps -vv -i oracle-xe-10.2.0.1-1.0.i386.rpm ... You must run '/etc/init.d/oracle-xe...

LEARN ABOUT DEBIAN

bup-margin

bup-margin(1)						      General Commands Manual						     bup-margin(1)

NAME

       bup-margin - figure out your deduplication safety margin

SYNOPSIS

       bup margin [options...]

DESCRIPTION

       bup margin  iterates  through  all  objects  in	your  bup repository, calculating the largest number of prefix bits shared between any two
       entries.  This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.

       For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45.  That  means  a  46-bit
       hash  would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
       its first 46 bits.

       The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects.  Since SHA-1 hashes have 160 bits,
       that  leaves 115 bits of margin.  Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
       with far fewer objects.

       If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see	if
       you're getting dangerously close to 160 bits.

OPTIONS

       --predict
	      Guess  the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
	      from the guess.  This is potentially useful for tuning an interpolation search algorithm.

       --ignore-midx
	      don't use .midx files, use only .idx files.  This is only really useful when used with --predict.

EXAMPLE

	      $ bup margin
	      Reading indexes: 100.00% (1612581/1612581), done.
	      40
	      40 matching prefix bits
	      1.94 bits per doubling
	      120 bits (61.86 doublings) remaining
	      4.19338e+18 times larger is possible

	      Everyone on earth could have 625878182 data sets
	      like yours, all in one repository, and we would
	      expect 1 object collision.

	      $ bup margin --predict
	      PackIdxList: using 1 index.
	      Reading indexes: 100.00% (1612581/1612581), done.
	      915 of 1612581 (0.057%)

SEE ALSO

       bup-midx(1), bup-save(1)

BUP

       Part of the bup(1) suite.

AUTHORS

       Avery Pennarun <apenwarr@gmail.com>.

Bup unknown-															     bup-margin(1)