Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
I have a Sun Ultra 10/Solaris 2.7 with a differential SCSI card connected to a Supter DLt1 Tape Drive. When I boot the machine, and I do a probe-scsi-all in the very beginning of the boot process. It shows up correctly. If I wait for the boot process to proceed and then I do a probe-scsi-all, I get... (1 Reply)
Sparc Ultra2:
Notes
prtdiag:
System Configuration: Sun Microsystems sun4u Sun Ultra 2 UPA/SBus (2 X UltraSPARC-II 296MHz)
System clock frequency: 99 MHz
Memory size: 768 Megabytes
========================= CPUs =========================
Run Ecache CPU CPU... (0 Replies)
Hi Guys,
I have a 2nd hand Sun ultra-5, I wanted to know how to be able to run it as a normal window. I do not have any experience whatsoever with solaris/unix. Does anyone can give me a clue where to start. When I switch it goes to:
unix console login:
pa$$word:
#UNIX sendmail : enable to... (0 Replies)
now what do i do?
im looking at it and i booted it after a bunch of code i got a line askign for the password
i also downloaded solaris 10
any advice on how to install it? (36 Replies)
Hello
I have Sun Ultra 10 with Solaris 7 installed on it.
Sometimes back
after that the machine use to get hang .Even after
rebooting the system was not booting.
I have manually switch on /off many times from the
power board itself .Once in a while it
use to boot .After... (12 Replies)
hi, my sun box hangs- KEYBOARD not found. Using hyper link it boots and then hangs without able to access or get ok promt
----SCREEN SHOT AS--------------------------------------------------
˙Loading onboard drivers: ebus i2c i2c i2c ppm
/ebus@1f,464000: flashprom rtc serial serial env-monitor... (2 Replies)
http://www.unix.com/images/smilies/mad.gif
Hi, this is parameswar. I have two sun ultra 5/10 workstations processor is sparc IIi 440 and ram is 512 but without hard disk and cdrom so can i use seagate 40Gb and sony dvd writer which is presented in windows pc. Both are IDE cables.
while I... (1 Reply)
Hi
I have just acquired an Ultra 5. It has 256MB of memory and a 360Mhz Ultra IIi SPARC processor. So far, I have had some typical fun and games to get it working:
- It had a dead NVRAM chip. I hacked it open and installed a CR2032. It looks suitably bodged up, but is working. I set the MAC... (8 Replies)
Discussion started by: _JonB_
8 Replies
LEARN ABOUT NETBSD
trm
TRM(4) BSD Kernel Interfaces Manual TRM(4)NAME
trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver
SYNOPSIS
trm* at pci? dev ? function ?
scsibus* at trm?
DESCRIPTION
The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.
HARDWARE
Supported SCSI controllers include:
Tekram DC-315 PCI Ultra SCSI adapter without flash BIOS and internal SCSI connector
Tekram DC-315U PCI Ultra SCSI adapter without flash BIOS
Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS
Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS
Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector
For Tekram DC-390 PCI SCSI host adapter, use pcscp(4) driver.
For Tekram DC-310/U and DC-390U/UW/F PCI SCSI host adapters, use siop(4) driver.
SEE ALSO cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), ss(4), st(4), uk(4), scsipi(9)
http://www.tekram.com/
AUTHORS
The trm driver was originally written for NetBSD 1.4/i386 by Erich Chen of Tekram Technology, and Rui-Xiang Guo rewrote the driver to use
bus_space(9) and bus_dma(9) for NetBSD 1.6.
BSD November 6, 2001 BSD