09-24-2003
what do you expect it to take it to?
i believe the default apache config already works with the local loop back.
what are you actually seeing? did you put anything in your server root? are you sure you are not just seeing the default apache page?
do you get a host not found error?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i'm trying to install netscape 6.01 on my linux system. I already have netscape 4.76 installed already. When i try to install netscape 6.01 it installs into a different place. So my origanal still works. when i run the script it seems to work. It goes to a part where its deferring registration... (2 Replies)
Discussion started by: kam1su2
2 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need help to install Netscape on AIX
Thank's:)
Operation System AIX 4.3
I has problem with configure MOZILLA_HOME (1 Reply)
Discussion started by: Niko
1 Replies
3. Post Here to Contact Site Administrators and Moderators
Were you aware that the forum entries don't show up in netscape 4.5.1. This is true on an NT box and a solaris box.
I changed my colors around on my winders box and checked to always use my colors. Unfortunately my company doesn't seem in any hurry to upgrade. It just means I have to ftp code... (7 Replies)
Discussion started by: gillbates
7 Replies
4. UNIX Desktop Questions & Answers
How can I find netscape for unix? I could only find for windows. I need netscape for solaris (3 Replies)
Discussion started by: kymberm
3 Replies
5. UNIX for Dummies Questions & Answers
Hi All..
I have netscape installed communicator 4.75 installed in my unix box. But dont know exactly how to use that as a browser.
I tried running it from installed dir. as shown below and got the following error.
testu:/opt/netscape >netscape
Error: Can't open display:... (1 Reply)
Discussion started by: ultimate
1 Replies
6. UNIX for Advanced & Expert Users
This question has been resolved. (0 Replies)
Discussion started by: system77
0 Replies
7. UNIX for Dummies Questions & Answers
when i try to open Netscape I get this:
Xlib: connection to "hpbox:0.0" refused by server
Xlib: Client is not Authorized to connect to server
Error: Can't open display: hpbox:0.0
Error Couldn't find per display information
*Note: I'm sharing a internet connection with my xp machine. Not... (2 Replies)
Discussion started by: Eric_Bakken
2 Replies
8. Solaris
I have been unable to locate any Netscape 9 or Firefox 2.0 packages for Solaris 8. Does anyone know if they are available anywhere?
Thanks in advance! (0 Replies)
Discussion started by: jalburger
0 Replies
9. Solaris
Hm am the perfect newbie:o
I handle an application on a production servers having a SunOS 5.8 and iplanet webserver instance. Users trying to access it on https are getting "Cannot find the server". I checked with the n/w and secuirty and they said traffic is allowed to the server. Everything... (6 Replies)
Discussion started by: JimmyJ
6 Replies
10. UNIX for Dummies Questions & Answers
I have an Ultra 5 machine with Solaris 8 installed as an operating system. To work with other PC's on my home network, I selected DHCP as the network protocol. I want to have Internet access on my Sun machine but have been unsuccessful. I had an old Netscape for Unix disk and installed it. The... (1 Reply)
Discussion started by: pb11545
1 Replies
LEARN ABOUT CENTOS
pmdaapache
PMDAAPACHE(1) General Commands Manual PMDAAPACHE(1)
NAME
pmdaapache - Apache2 web server performance metrics domain agent (PMDA)
SYNOPSIS
$PCP_PMDAS_DIR/apache/pmdaapache [-d domain] [-l logfile] [-U username] [-S server] [-P port] [-L location]
DESCRIPTION
pmdaapache is a Performance Metrics Domain Agent (PMDA) which extracts performance metrics describing the state of an Apache web server.
The apache PMDA exports metrics that measure the request rate, cumulative request sizes, uptime and various connection states for active
clients.
This information is obtained by performing a HTTP request to the server status URL, which must be enabled in the httpd.conf configuration
file.
ExtendedStatus on
<Location /server-status>
SetHandler server-status
Order deny,allow
Deny from all
Allow from localhost
</Location>
A brief description of the pmdaapache command line options follows:
-d It is absolutely crucial that the performance metrics domain number specified here is unique and consistent. That is, domain should
be different for every PMDA on the one host, and the same domain number should be used for the same PMDA on all hosts.
-l Location of the log file. By default, a log file named apache.log is written in the current directory of pmcd(1) when pmdaapache is
started, i.e. $PCP_LOG_DIR/pmcd . If the log file cannot be created or is not writable, output is written to the standard error
instead.
-S Query the Apache status information from the named server rather than the local host.
-P Query the Apache status information from the given port rather than the default (80).
-L Specify an alternative location for finding the server-status page.
-U User account under which to run the agent. The default is the unprivileged "pcp" account in current versions of PCP, but in older
versions the superuser account ("root") was used by default.
INSTALLATION
If you want access to the names, help text and values for the apache performance metrics, do the following as root:
# cd $PCP_PMDAS_DIR/apache
# ./Install
If you want to undo the installation, do the following as root:
# cd $PCP_PMDAS_DIR/apache
# ./Remove
pmdaapache is launched by pmcd(1) and should never be executed directly. The Install and Remove scripts notify pmcd(1) when the agent is
installed or removed.
FILES
$PCP_PMCDCONF_PATH
command line options used to launch pmdaapache
$PCP_PMDAS_DIR/apache/help
default help text file for the apache metrics
$PCP_PMDAS_DIR/apache/Install
installation script for the pmdaapache agent
$PCP_PMDAS_DIR/apache/Remove
undo installation script for the pmdaapache agent
$PCP_LOG_DIR/pmcd/apache.log
default log file for error messages and other information from pmdaapache
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
SEE ALSO
PCPIntro(1), httpd(8), pmcd(1), pcp.conf(5) and pcp.env(5).
Performance Co-Pilot PCP PMDAAPACHE(1)