09-18-2003
scan / mount options
Hi,
you want to permit the scanning of your filesystems at boot time ? The first way I would say is changing the mount options in the fstab file, if you replace 1 2 with 0 0 the filesystem will not be checked at boot time.
Alex
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi guys,
May I know how to install Solaris 8 in the way that I can triple boot it with my the other two OS: WIndows ME and Windows 2000 Pro.
Can you all please kindly advise me on how to setup the triple boot process inorder to allow Windows ME to be the default OS when being ask to choose... (1 Reply)
Discussion started by: cia
1 Replies
2. UNIX for Advanced & Expert Users
Hello there
I need to run a script whenever i reboot or startup my HP-UX server. This script adds some routes to the route table, and it start third party aplications like "Star Manager".
I thought i could do this simply putting the script in "/sbin/init.d,
and a link to the script in... (7 Replies)
Discussion started by: vascobrito
7 Replies
3. UNIX for Dummies Questions & Answers
Hi all
The following error was displayed when a sco server (5.0.5) was booted. What should be done to overcome the problem. Replies appreciated.
Bios 03.0
0130688 KB memory good
01 processor(s) in system
remote console dialing on, please wait
connect fail : modem off
cpu clock... (6 Replies)
Discussion started by: raguramtgr
6 Replies
4. UNIX for Dummies Questions & Answers
Evry time I start up my mavhine ,have to type in unix at
Boot
:
Is there a way unix should bootup automatically?
Asif (2 Replies)
Discussion started by: asif iqbal
2 Replies
5. UNIX for Dummies Questions & Answers
What is the boot up sequence in UNIX? (2 Replies)
Discussion started by: karthi_g
2 Replies
6. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT NETBSD
quotacheck
QUOTACHECK(8) BSD System Manager's Manual QUOTACHECK(8)
NAME
quotacheck -- filesystem quota consistency checker
SYNOPSIS
quotacheck [-gquv] filesystem ...
quotacheck [-gquv] [-l maxparallel] -a
DESCRIPTION
quotacheck examines each filesystem, builds a table of current disk usage, and compares this table against that recorded in the disk quota
file for the filesystem. If any inconsistencies are detected, both the quota file and the current system copy of the incorrect quotas are
updated (the latter only occurs if an active filesystem is checked). By default both user and group quotas are checked.
Available options:
-a If the -a flag is supplied in place of any filesystem names, quotacheck will check all the filesystems indicated in /etc/fstab to be
read-write with disk quotas. By default only the types of quotas listed in /etc/fstab are checked. See also -l.
-g Only group quotas listed in /etc/fstab are to be checked. See also -u.
-l maxparallel
Limit the number of parallel checks to the number specified in the following argument. By default, the limit is the number of disks,
running one process per disk. If a smaller limit is given, the disks are checked round-robin, one file system at a time. This
option is only valid with -a.
-q quotacheck runs more quickly, particularly on systems with sparse user id usage, but fails to correct quotas for users [groups] not
in the system user [group] database, and owning no files on the filesystem, if the quota file incorrectly believes that they do.
-u Only user quotas listed in /etc/fstab are to be checked. See also -g.
-v quotacheck is more verbose, and reports corrected discrepancies between the calculated and recorded disk quotas.
Specifying both -g and -u is equivalent to the default. Parallel passes are run on the filesystems required, using the pass numbers in
/etc/fstab in an identical fashion to fsck(8).
Normally quotacheck operates silently.
quotacheck expects each filesystem to be checked to have a quota files named quota.user and quota.group which are located at the root of the
associated file system. These defaults may be overridden in /etc/fstab. If a file is not present, quotacheck will create it.
quotacheck is normally run at boot time from the /etc/rc file, see rc(8), before enabling disk quotas with quotaon(8).
quotacheck accesses the raw device in calculating the actual disk usage for each user. Thus, the filesystems checked should be quiescent
while quotacheck is running.
If quotacheck receives a SIGINFO signal (see the status argument for stty(1)), a line will be written to the standard error output indicating
the name of the device currently being checked and progress information.
FILES
quota.user at the filesystem root with user quotas
quota.group at the filesystem root with group quotas
/etc/fstab default filesystems
SEE ALSO
quota(1), libquota(3), fstab(5), edquota(8), fsck(8), quotaon(8), repquota(8)
HISTORY
The quotacheck command appeared in 4.2BSD.
BSD
January 5, 2004 BSD