08-29-2003
setting a route in Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
I was told this worked on an HP system (same network as the sun server I am trying to set this up on)> but I get "netmask: bad value"2when I try it on the Sun:
route add net 199.42.23.192 netmask 255.255.255.192 204.104.63.30 1
I've tried many different iterations (leaving out netmask, only... (2 Replies)
Discussion started by: nhmeanie
2 Replies
5. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
6. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)
NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) ifsysctl(8)
sysconfig December 2009 IFNDP-PROXY(5)