08-29-2003
setting a route in Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
I was told this worked on an HP system (same network as the sun server I am trying to set this up on)> but I get "netmask: bad value"2when I try it on the Sun:
route add net 199.42.23.192 netmask 255.255.255.192 204.104.63.30 1
I've tried many different iterations (leaving out netmask, only... (2 Replies)
Discussion started by: nhmeanie
2 Replies
5. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
6. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT DEBIAN
oidentd_masq.conf
oidentd_masq.conf(5) File Formats Manual oidentd_masq.conf(5)
NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file.
DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is
specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file.
oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option.
This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident
daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons
for windows do this, maybe others).
FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type>
The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The
mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is
equivalent to 255.255.0.0, etc.
The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param-
eter.
The third field specifies the operating system the machine matching the first parameter is running.
EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type>
192.168.1.1 someone UNIX
192.168.1.2 noone WINDOWS
192.168.1.1/32 user1 UNIX
192.168.1.0/24 user3 UNIX
192.168.0.0/16 user4 UNIX
somehost user5 UNIX
192.168.1.0/255.255.255.0 user6 UNIX
AUTHOR
Ryan McCabe <ryan@numb.org>
http://dev.ojnk.net
SEE ALSO
oidentd(8) oidentd.conf(5)
version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)