08-29-2003
setting a route in Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
I was told this worked on an HP system (same network as the sun server I am trying to set this up on)> but I get "netmask: bad value"2when I try it on the Sun:
route add net 199.42.23.192 netmask 255.255.255.192 204.104.63.30 1
I've tried many different iterations (leaving out netmask, only... (2 Replies)
Discussion started by: nhmeanie
2 Replies
5. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
6. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT DEBIAN
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <stgt@vger.kernel.org>
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)