info regarding meta device Post: 37968

4 More Discussions You Might Find Interesting

1. Solaris

pseudo: [ID 129642 kern.info] pseudo-device: vol0

Hi I have a system that gave me some messages on bootup that I was not used to seeing: pseudo: pseudo-device: vol0 genunix: vol0 is /pseudo/vol@0 these came with these: Feb 13 17:42:17 system1 eri: SUNW,eri0 : 100 Mbps full duplex link up Feb 13 17:42:21 system1sendmail: My unqualified...

2. UNIX for Advanced & Expert Users

howto remove meta info about MP4 or FLV file downloaded off Youtube?

Hi I tried a tool called mediainfo > brew info media-info media-info 0.7.51 http://mediainfo.sourceforge.net Depends on: pkg-config /usr/local/Cellar/media-info/0.7.51 (3 files, 14M) http://github.com/mxcl/homebrew/commits/master/Library/Formula/media-info.rb Got details from a test...

3. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ...

4. HP-UX

Failed to open tape device /dev/rmt/0mn:Device busy (errno = 16)

Hi, Unable to make tape backup, please help. /opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00 * Creating local directories for configuration files and archive. ======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery. (Mon...

LEARN ABOUT DEBIAN

hd

HD(4)							     Linux Programmer's Manual							     HD(4)

NAME

       hd - MFM/IDE hard disk devices

DESCRIPTION

       The  hd*  devices  are block devices to access MFM/IDE hard disk drives in raw mode.  The master drive on the primary IDE controller (major
       device number 3) is hda; the slave drive is hdb.  The master drive of the second controller (major device number 22) is hdc and	the  slave
       hdd.

       General	IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
       partition on that physical drive.  The first form, hdX, is used to address the whole drive.  Partition numbers are assigned  in	the  order
       the  partitions	are  discovered,  and only nonempty, nonextended partitions get a number.  However, partition numbers 1-4 are given to the
       four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended.  Thus, the first  logi-
       cal  partition  will be hdX5.  Both DOS-type partitioning and BSD-disklabel partitioning are supported.	You can have at most 63 partitions
       on an IDE disk.

       For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on  the
       second one.

       They are typically created by:

	      mknod -m 660 /dev/hda b 3 0
	      mknod -m 660 /dev/hda1 b 3 1
	      mknod -m 660 /dev/hda2 b 3 2
	      ...
	      mknod -m 660 /dev/hda8 b 3 8
	      mknod -m 660 /dev/hdb b 3 64
	      mknod -m 660 /dev/hdb1 b 3 65
	      mknod -m 660 /dev/hdb2 b 3 66
	      ...
	      mknod -m 660 /dev/hdb8 b 3 72
	      chown root:disk /dev/hd*

FILES

       /dev/hd*

SEE ALSO

       chown(1), mknod(1), sd(4), mount(8)

COLOPHON

       This  page is part of release 3.44 of the Linux man-pages project.  A description of the project, and information about reporting bugs, can
       be found at http://www.kernel.org/doc/man-pages/.

Linux								    1992-12-17								     HD(4)