06-16-2003
If the ethernet card is not listed in the Linux "Hardware HowTo" then you will have trouble getting it to work with Linux.
Your best best is to buy a cheap card that *is* supported and install it in one of your unused PCI slots...... Neo
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
piv-tool
PIV-TOOL(1) OpenSC Tools PIV-TOOL(1)
NAME
piv-tool - smart card utility for HSPD-12 PIV cards
SYNOPSIS
piv-tool [OPTIONS]
The piv-tool utility can be used from the command line to perform miscellaneous smart card operations on a HSPD-12 PIV smart card as
defined in NIST 800-73-3. It is intened for use with test cards only. It can be used to load objects, and generate key pairs, as well as
send arbitrary APDU commands to a card after having authenticated to the card using the card key provided by the card vendor.
OPTIONS
--serial
Print the card serial number derived from the CHUID object, if any. Output is in hex byte format.
--name, -n
Print the name of the inserted card (driver)
--admin argument, -A argument
Authenticate to the card using a 2DES or 3DES key. The argument of the form
{A|M}:ref:alg
is required, were A uses "EXTERNAL AUTHENTICATION" and M uses "MUTUAL AUTHENTICATION". ref is normally 9B, and alg is 03 for 3DES. The
key is provided by the card vendor, and the environment variable PIV_EXT_AUTH_KEY must point to a text file containing the key in the
format: XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX
--genkey argument, -G argument
Generate a key pair on the card and output the public key. The argument of th form
ref:alg
is required, where ref is 9A, 9C, 9D or 9E and alg is 06, 07, 11 or 14 for RSA 1024, RSA 2048, ECC 256 or ECC 384 respectively.
--object ContainerID, -O ContainerID
Load an object on to the card. The ContainerID is as defined in NIST 800-73-n without leading 0x. Example: CHUID object is 3000
--cert ref, -s ref
Load a certificate on to the card. ref is 9A, 9C, 9D or 9E
--compresscert ref, -Z ref
Load a certificate that has been gziped on to the card. ref is 9A, 9C, 9D or 9E
--out file, -o file
Output file for any operation that produces output.
--in file, -i file
Input file for any operation that requires an input file.
--key-slots-discovery file
Print properties of the key slots. Needs 'admin' authentication.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF.... This option may be repeated.
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--wait, -w
Wait for a card to be inserted
--verbose, -v
Causes piv-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
SEE ALSO
opensc-tool(1)
opensc 06/17/2014 PIV-TOOL(1)