Sponsored Content
Full Discussion: network card problem
Top Forums UNIX for Advanced & Expert Users network card problem Post 36606 by q30 on Sunday 1st of June 2003 10:32:48 PM
Old 06-01-2003
network card problem

hi, everyone:

alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up :negotiated 100BaseTX:full duplex"
ˇ°tu0 :transmit FIFO underflow:threshold raised to :512 byte, link up :negotiated 100BaseTX:full duplex"

help me! thanks a lot!
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Network Card Problem On Linux

Hi I just installed linux red hat 7.0 and i can't connect the machine on the network. Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize. Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies

3. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

4. UNIX for Dummies Questions & Answers

Network card problem, wrong IRQ

I've installed mandrake 9 and from the start my network card wouldn't work. I ran the network configuration wizard several times and counldn't get it to work. I checked Linux and in the boot message said the IRQ for my network card was 0 but wheni checked windows XP it listed it as 23. I have a... (1 Reply)
Discussion started by: ripmc
1 Replies

5. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

6. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

7. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

8. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

9. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
SYSTEMD-NETWORKD.SERVICE(8)				     systemd-networkd.service				       SYSTEMD-NETWORKD.SERVICE(8)

NAME
systemd-networkd.service, systemd-networkd - Network manager SYNOPSIS
systemd-networkd.service /lib/systemd/systemd-networkd DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating virtual network devices. To configure low-level link settings independently of networks, see systemd.link(5). systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in those files. systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match] section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by using Unmanaged=yes option, see systemd.network(5). When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up manually. CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network directory /run/systemd/network and the local administration network directory /etc/systemd/network. Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see systemd.netdev(5). SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8) systemd 237 SYSTEMD-NETWORKD.SERVICE(8)
All times are GMT -4. The time now is 10:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy