Ultra 3 scsi card Post: 35597

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve...

2. Solaris

problems with my M3 video card and my Tatung Ultra 10 clone

i took this Elite 3D M3 video card out of my Ultra 60 machine which was replaced with an M6. the card was working w/o issue in the Ultra 60. however, i'm getting no video when i power the Tatung machine. yes, the M3 is does work with an AXi motherboard. any ideas what's causing the problem?

3. Solaris

Problem with SCSI DAT drive on Ultra 10

I will be honest I am quite new to UNIX and Solaris so this may be a simple thing. I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10. I have previously fitted a SCSI card to the box which has configured ok and can be seen from...

4. SCO

configure Adaptec 29320ALP Ultra 320 SCSI Card in IBM X3400

I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120...

5. Solaris

Sparcstation 5 graphics card in Ultra 1 server

is it possible to swap the Turbo XGX graphics card in the SS5 to the ULTRA server 1 ? and do they use the same type of RAM ? Thx.

6. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon

7. UNIX for Dummies Questions & Answers

installing scsi card

i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me.

8. UNIX for Dummies Questions & Answers

Problems with SCSI card and tape drive

Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system...

9. Solaris

Connect an External SCSI Hard Drive to Ultra 80

Guys, I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem. I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80. I connected it powered it up and at OK prompt did : boot -r system comes up and complains about not...

10. Solaris

Solaris 10 SCSI card question

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance.

LEARN ABOUT CENTOS

tapset::scsi

tapset::scsi(3stap)													       tapset::scsi(3stap)

NAME

       tapset::scsi - systemtap scsi tapset

DESCRIPTION

	This family of probe points is used to probe SCSI activities.

       scsi.ioentry
	      Prepares a SCSI mid-layer request

	       See probe::scsi.ioentry(3stap)
	       for details.

       scsi.iodispatching
	      SCSI mid-layer dispatched low-level SCSI command

	       See probe::scsi.iodispatching(3stap)
	       for details.

       scsi.iodone
	      SCSI command completed by low level driver and enqueued into the done queue.

	       See probe::scsi.iodone(3stap)
	       for details.

       scsi.iocompleted
	      SCSI mid-layer running the completion processing for block device I/O requests

	       See probe::scsi.iocompleted(3stap)
	       for details.

       scsi.ioexecute
	      Create mid-layer SCSI request and wait for the result

	       See probe::scsi.ioexecute(3stap)
	       for details.

       scsi.set_state
	      Order SCSI device state change

	       See probe::scsi.set_state(3stap)
	       for details.

SEE ALSO

	  probe::scsi.ioentry(3stap),	   probe::scsi.iodispatching(3stap),	  probe::scsi.iodone(3stap),	 probe::scsi.iocompleted(3stap),
       probe::scsi.ioexecute(3stap),  probe::scsi.set_state(3stap),  stap(1), stapprobes(3stap)

IBM
									---						       tapset::scsi(3stap)

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

Discussion started by: s_aamir

2. Solaris

problems with my M3 video card and my Tatung Ultra 10 clone

Discussion started by: xyyz

3. Solaris

Problem with SCSI DAT drive on Ultra 10

Discussion started by: mattw

4. SCO

configure Adaptec 29320ALP Ultra 320 SCSI Card in IBM X3400

Discussion started by: hafizurr