03-18-2003
I got this to work after I reinstalled the OS. The card was detected fine and it was up and running in no time.
9 More Discussions You Might Find Interesting
1. IP Networking
I have a solaris 9 system that cannot get to the internet and cannot ping outside of the router. I can ping any other system on this campus but when i try to ping any other system outside of the campus im on i get unreachable.
Here is the systems info:
ip: 10.241.3.254
subnet: 255.254.0.0... (7 Replies)
Discussion started by: meyersp
7 Replies
2. Filesystems, Disks and Memory
Hi,
I have a network disk that runs windows xp embedded. It doesnt support NFS.
But Samba is supported.
How do i connect to it through solaris 9. What are the steps required.
I have the IP address of the drive.
Thanks (1 Reply)
Discussion started by: R00tSc0rpi0n
1 Replies
3. IP Networking
Hi.. I have problem about connecting two network. First let me tell about my project. I use Quagga to build up IPv6 Island Network. At first, i build one (1) PC Router or one (1) network, i call it as Network A. All PC's or Laptop's (node's) that connect to Network A can communicated to each other... (4 Replies)
Discussion started by: Lieyza
4 Replies
4. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
5. Solaris
I want to install Solaris 11 Express on my x86 system.
I'm facing network driver problems.
I've 3 network cards:
1. Intel(R) 82579V Gigabit Network Connection
In Device Driver Utility, This device is displayed as Ethernet controller, Driver is UNK and its highlighted in RED.
2. Belkin... (3 Replies)
Discussion started by: choudharypranay
3 Replies
6. Shell Programming and Scripting
Hello all,
Here is the explanation of my problem:
I have a cronjob that connects to a NAS to do backups from my laptop to this NAS device.
The script that I wrote does check if there is a host (the NAS) responding on 192.168.1.10 and tries to connect to it with the following command:
mount -v... (3 Replies)
Discussion started by: freddie50
3 Replies
7. UNIX for Dummies Questions & Answers
Have -
-3 HP Proliant G4P servers - Debian (wheezy)
-3 RaspPI's - Raspian
-Unmanaged switch that all 6 can ssh into each other with via eth0
-Router (w wifi and 5 ports) - on eth1 of the three G4p's of protocol dhcp
Want:
To let the six servers, in my basement run, since the HPs are... (5 Replies)
Discussion started by: sas
5 Replies
8. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
9. Solaris
Seems to wanboot ok but then fails to connect to server. What do I need to check?
{0} ok boot net - install
Boot device: /pci@300/pci@1/pci@0/pci@1/network@0 File and args: - install
1G link up
<time unavailable> wanboot info: WAN boot messages->console
<time unavailable>... (2 Replies)
Discussion started by: psychocandy
2 Replies
LEARN ABOUT OPENDARWIN
ypset
YPSET(8) BSD System Manager's Manual YPSET(8)
NAME
ypset -- tell ypbind(8) which YP server process to use
SYNOPSIS
ypset [-h host] [-d domain] server
DESCRIPTION
Ypset tells the ypbind(8) process on the current machine which YP server process to communicate with. If server is down or is not running a
YP server process, it is not discovered until a YP client process attempts to access a YP map, at which time ypbind(8) tests the binding and
takes appropriate action.
Ypset is most useful for binding a YP client that is not on the same broadcast network as the closest YP server, but can also be used for
debugging a local network's YP configuration, testing specific YP client programs, or binding to a specific server when there are many
servers on the local network supplying YP maps.
The options are as follows:
-h host
Set the YP binding on host instead of the local machine.
-d domain
Use the YP domain domain instead of the default domain as returned by domainname(1).
SEE ALSO
domainname(1), ypbind(8), ypcat(1), ypmatch(1), yppoll(8), ypwhich(1), yp(8)
AUTHOR
Theo de Raadt
BSD
October 25, 1994 BSD