Sponsored Content
Special Forums IP Networking Connect: Network is unreachable Post 34780 by skotapal on Tuesday 11th of March 2003 06:59:51 PM
Old 03-11-2003
Connect: Network is unreachable

I am running RH7.3 on a compaq presario box. The network card is a Linksys one. I am only able to communicate with the local network (only the local IPs are accessible). When I try to ping another box I get a "Connect: Network is unreachable" message. What could be the problem.

Thanks in advance!
 

9 More Discussions You Might Find Interesting

1. IP Networking

Cannot connect to rest of network/internet

I have a solaris 9 system that cannot get to the internet and cannot ping outside of the router. I can ping any other system on this campus but when i try to ping any other system outside of the campus im on i get unreachable. Here is the systems info: ip: 10.241.3.254 subnet: 255.254.0.0... (7 Replies)
Discussion started by: meyersp
7 Replies

2. Filesystems, Disks and Memory

How to connect to a Network disk using SAMBA

Hi, I have a network disk that runs windows xp embedded. It doesnt support NFS. But Samba is supported. How do i connect to it through solaris 9. What are the steps required. I have the IP address of the drive. Thanks (1 Reply)
Discussion started by: R00tSc0rpi0n
1 Replies

3. IP Networking

Can AnyOne Help Me (connect two network)

Hi.. I have problem about connecting two network. First let me tell about my project. I use Quagga to build up IPv6 Island Network. At first, i build one (1) PC Router or one (1) network, i call it as Network A. All PC's or Laptop's (node's) that connect to Network A can communicated to each other... (4 Replies)
Discussion started by: Lieyza
4 Replies

4. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

5. Solaris

Cannot connect to network in Solaris 11

I want to install Solaris 11 Express on my x86 system. I'm facing network driver problems. I've 3 network cards: 1. Intel(R) 82579V Gigabit Network Connection In Device Driver Utility, This device is displayed as Ethernet controller, Driver is UNK and its highlighted in RED. 2. Belkin... (3 Replies)
Discussion started by: choudharypranay
3 Replies

6. Shell Programming and Scripting

How to identify a network device before trying to connect to it?

Hello all, Here is the explanation of my problem: I have a cronjob that connects to a NAS to do backups from my laptop to this NAS device. The script that I wrote does check if there is a host (the NAS) responding on 192.168.1.10 and tries to connect to it with the following command: mount -v... (3 Replies)
Discussion started by: freddie50
3 Replies

7. UNIX for Dummies Questions & Answers

Connect to my Linux network remotely?

Have - -3 HP Proliant G4P servers - Debian (wheezy) -3 RaspPI's - Raspian -Unmanaged switch that all 6 can ssh into each other with via eth0 -Router (w wifi and 5 ports) - on eth1 of the three G4p's of protocol dhcp Want: To let the six servers, in my basement run, since the HPs are... (5 Replies)
Discussion started by: sas
5 Replies

8. Ubuntu

Could not connect to wireless network

I run lubuntu from usb (try lubuntu, it's not install on my pc ) And i try to connect to network I see the network name And i put the pass But it's not connect.. I tried to open hot spot on my phone and try to connect and it's not connect I have edumax n150 Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies

9. Solaris

Installadm - network in unreachable

Seems to wanboot ok but then fails to connect to server. What do I need to check? {0} ok boot net - install Boot device: /pci@300/pci@1/pci@0/pci@1/network@0 File and args: - install 1G link up <time unavailable> wanboot info: WAN boot messages->console <time unavailable>... (2 Replies)
Discussion started by: psychocandy
2 Replies
NETWORKS(5)							File Formats Manual						       NETWORKS(5)

NAME
networks - network name data base DESCRIPTION
The networks file contains information regarding the known networks which comprise the DARPA Internet. For each network a single line should be present with the following information: official network name network number aliases Items are separated by any number of blanks and/or tab characters. A ``#'' indicates the beginning of a comment; characters up to the end of the line are not interpreted by routines which search the file. This file is normally created from the official network data base main- tained at the Network Information Control Center (NIC), though local changes may be required to bring it up to date regarding unofficial aliases and/or unknown networks. Network number may be specified in the conventional ``.'' notation using the inet_network() routine from the Internet address manipulation library, inet(3N). Network names may contain any printable character other than a field delimiter, newline, or comment character. FILES
/etc/networks SEE ALSO
getnetent(3N) BUGS
A name server should be used instead of a static file. 4.2 Berkeley Distribution May 6, 1986 NETWORKS(5)
All times are GMT -4. The time now is 06:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy