Sponsored Content
Full Discussion: IPSec - VPN using shared key
Special Forums Cybersecurity IPSec - VPN using shared key Post 34239 by eNTer on Tuesday 11th of February 2003 09:56:59 AM
Old 02-11-2003
My real problem is that the Linux gateway is using a "pre-shared ke", while the xBSD gateway is asking different keys with different encryption styles: encryption key and auth key. That i did not figure out: why BSD needs different keys and FreeSWAN/ipsec does not, or how can a BSD gateway talk to a FreeSWAN/Linux gateway with PSK?
 

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

How to interpret the shared memory key

I'm facing a problem interpreting the shared memory key on an AIX machine. (1) I go to a property file and I see the following: shm_key = "119112066" (2) So I now go the command prompt and do this: ipcs -m | grep 119112066 And, I do not find it. So what I do is to run the... (2 Replies)
Discussion started by: vijaygade
2 Replies

2. IP Networking

IPSec VPN Routing

Hello, I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue. ... (0 Replies)
Discussion started by: salukibob
0 Replies

3. Solaris

Solaris 8 ssh public key authentication issue - Server refused our key

Hi, I've used the following way to set ssh public key authentication and it is working fine on Solaris 10, RedHat Linux and SuSE Linux servers without any problem. But I got error 'Server refused our key' on Solaris 8 system. Solaris 8 uses SSH2 too. Why? Please help. Thanks. ... (1 Reply)
Discussion started by: aixlover
1 Replies

4. Cybersecurity

IPSEC

hello, after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration! I also generate different key for AH and ESP as i have shown below. what is my problem and what should i do to have ping and test the configuration? code: ... (0 Replies)
Discussion started by: elinaz
0 Replies

5. Programming

Shared library with acces to shared memory.

Hello. I am new to this forum and I would like to ask for advice about low level POSIX programming. I have to implement a POSIX compliant C shared library. A file will have some variables and the shared library will have some functions which need those variables. There is one special... (5 Replies)
Discussion started by: iamjag
5 Replies

6. IP Networking

VPN IPSec Openswan

Hi all, I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
Discussion started by: ivancd
4 Replies

7. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

8. IP Networking

Best tool to monitor VPN IPSEC Tunneling

We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug. Please suggest what may be the cause for the above mentioned issue. Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
KUMO-GATEWAY(1) 					      General Commands Manual						   KUMO-GATEWAY(1)

NAME
kumo-gateway - kumofs gateway daemon SYNOPSIS
kumo-gateway -m <addr[:port]> -p <addr[:port]> [-t port] [-b port] [-c port] DESCRIPTION
kumo-gateway receives requests from applications and relays it to the kumo-servers. Run this daemon on the hosts that runs applications that uses kumofs. OPTIONS
-m <addr[:port=19700]> --manager1 address of manager 1 -p <addr[:port=19700]> --manager2 address of manager 2 -lc --local-cache local cache (Tokyo Cabinet abstract database) -t <[addr:]port=11411> --memproto-text memcached text protocol listen port -b <[addr:]port=11511> --memproto-binary memcached binary protocol listen port -c <[addr:]port=11611> --cloudy asynchronous memcached binary protocol listen port -F --memproto-save-flag save flags on memcached text protocol -As --async-replicate-set send response without waiting replication on set -Ad --async-replicate-delete send response without waiting replication on delete -G <number=5> --get-retry get retry limit -S <number=20> --set-retry set retry limit -D <number=20> --delete-retry delete retry limit -rn <number=4> --renew-threshold hash space renew threshold -k <number=2> --keepalive-interval keepalive interval in seconds -Ys <number=1> --connect-timeout connect timeout time in seconds -Yn <number=4> --connect-retry-limit connect retry limit -Ci <number=2> --clock-interval clock interval in seconds -TW <number=2> --write-threads number of threads for asynchronous writing -TR <number=4> --read-threads number of threads for asynchronous reading -o <path.log> --log output logs to the file -g <path.mpac> --binary-log enable binary log -v --verbose -d <path.pid> --daemon EXAMPLE
[on cli1 ]$ kumo-gateway -v -m mgr1 -p mgr2 -t 11211 -As -Ad [localhost]$ kumo-gateway -v -m localhost -t 11211 -d kumo-gateway.pid SEE ALSO
kumolog(1). kumo-gateway July 2009 KUMO-GATEWAY(1)

Featured Tech Videos

All times are GMT -4. The time now is 11:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy