|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Disk Array & Clustering
Post 34092 by champion on Tuesday 4th of February 2003 03:25:53 AM
02-04-2003
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Do you know how do I make my solaris 8 detect the storEDGE A5000?.
I have problem making it recognise, without that I cannot install VxVM.
Any ideas? (7 Replies)
Discussion started by: calsum
7 Replies
2. Solaris
I am new to the unix world. I have SunBlade 100 and A1000 Disk storage array with 12 Hard drives. I used SCSI card and SCSI cables to connect. When I do the format command,I can see disk storage as one disk instead of 12 disks as below. Could anybody can explain why?
What should I do in order... (1 Reply)
Discussion started by: Dulasi
1 Replies
3. UNIX for Advanced & Expert Users
I have a 3510 disk array attached to a T2000 server.
The dmesg command shows disk error as follows and is generated a couple of times during the day
Aug 18 03:35:51 myserver SUNWscsdMonitor: <rctrl6042> Standard General Event, CHL:2 ID:22 Drive NOTICE: Drive Recovered Error - 5F8E1F... (1 Reply)
Discussion started by: Tirmazi
1 Replies
4. Solaris
I would want to ask on what software do i need to configure disk array for StorEdge A1000. (Sun Enterprise 450 - currently installed with SUN Solaris 9.)
Is it using RAID Manager 6.22? And is it compatible with SUN Solaris 9 or 10?
Thanks in advance for reading or replying my post. (2 Replies)
Discussion started by: beginningDBA
2 Replies
5. Solaris
So I have 2 solaris sun servers one with a disk array with 14 drives which I need to move to the other server. How do I move the disk array configured as a Raid 5 to another server without losing data? So far I know I'll connect the drive, run devfsadm, use format to verify the server see's... (5 Replies)
Discussion started by: Kjons76
5 Replies
6. UNIX for Advanced & Expert Users
HI:
I have a DUAL redundant system running in HP-UX 10.20 ( 2 servers)
Both servers share an external SCSI disk array. Both server runs a Data base wich uses the disk array to write the data, and that is the way they share the information.
The way that the servers see the disk array, is like... (1 Reply)
Discussion started by: pmoren
1 Replies
7. UNIX for Dummies Questions & Answers
Hi there,
I've setup a raid0 array of 3 identical disks using :
mdadm --create --verbose /dev/md0 --level=stripe --raid-devices=3 /dev/sdb1 /dev/sdc1 /dev/sdd1I'm using dstat to monitor the disk activity :
dstat --epoch -D sdb,sdc,sdd --disk-util 30The results show that the stress is not... (8 Replies)
Discussion started by: chebarbudo
8 Replies
8. UNIX for Advanced & Expert Users
The disk drive for /tmp is not ready yet or not present && the disk drive for /boot is not ready yet
Hi Team
when I boot the server I get this 2 errors :
the disk drive for /tmp is not ready yet or not present
the disk drive for /boot is not ready yet or not present
and its stay like that , I m using Ubuntu 12.04
please if someone have any idea how to fix that problem . (1 Reply)
Discussion started by: SULTAN01
1 Replies
9. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
10. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
LEARN ABOUT DEBIAN
moosex::attributehelpers::methodprovider::array
MooseX::AttributeHelpers::MethodProvider::Array(3pm) User Contributed Perl Documentation MooseX::AttributeHelpers::MethodProvider::Array(3pm) NAME
MooseX::AttributeHelpers::MethodProvider::Array - method generator for MooseX::AttributeHelpers::Collection::Array DESCRIPTION
This is a role which provides the method generators for MooseX::AttributeHelpers::Collection::Array. METHODS
meta PROVIDED METHODS
This module also consumes the List method providers, to see those provied methods, refer to that documentation. get pop push set shift unshift clear delete insert splice sort_in_place Sorts the array in place, modifying the value of the attribute. You can provide an optional subroutine reference to sort with (as you can with the core "sort" function). However, instead of using $a and $b, you will need to use $_[0] and $_[1] instead. accessor If passed one argument, returns the value of the requested element. If passed two arguments, sets the value of the requested element. BUGS
All complex software has bugs lurking in it, and this module is no exception. If you find a bug please either email me, or add the bug to cpan-RT. AUTHOR
Stevan Little <stevan@iinteractive.com> COPYRIGHT AND LICENSE
Copyright 2007-2009 by Infinity Interactive, Inc. <http://www.iinteractive.com> This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself. perl v5.10.1 2010-01-02 MooseX::AttributeHelpers::MethodProvider::Array(3pm)