Sponsored Content
Full Discussion: Annex Terminal Server
Top Forums UNIX for Advanced & Expert Users Annex Terminal Server Post 33873 by kie on Wednesday 22nd of January 2003 10:28:04 AM
Old 01-22-2003
thanks I'll check it out.

I've got to the point of uploading the image I can get it to boot but can't edit config.annex.

I'll keep working and let you know if I get it sorted


Kie
 

10 More Discussions You Might Find Interesting

1. Solaris

Sun Server Hyper Terminal

Anyone know how to connect to a sun server using serial cable my client PC is also a Sun !!! I have the cable , just do not know how to start a terminal session in Sun . (1 Reply)
Discussion started by: civic2005
1 Replies

2. Solaris

Booting Up Servers from the Terminal Server.

All, I have a problem with booting up of servers. I am involved in application programming(Perl/Shell), but don't have much hardware knowledge about the Sun Solaris Server's we use. Our Development Servers are located at a remote place from the Development Centre. Every time there is a Power... (1 Reply)
Discussion started by: rahulrathod
1 Replies

3. UNIX for Advanced & Expert Users

terminal setting in unix server

hi all, i have connected a new dump terminal to unix server.the connection is not direct.it is through a board. that is a board which contain lot of ports is connected to server. the terminals are connected to the board.when i connected the terminal to the server the message in terminal is like... (0 Replies)
Discussion started by: sujesh
0 Replies

4. Solaris

How do I get basic server specs from terminal?

Hi there. Anyone know how to get CPU speed, RAM size etc (basic specs) from a SUN server running solaris, from the unix terminal? I'm sure there must be a command for this but ... I haven't been able to find it so far.. :o Cheers. (8 Replies)
Discussion started by: kenny123m
8 Replies

5. Cybersecurity

ssh to terminal server

Hi. We are currently upgrading the terminal server in our system (Solaris 8). Previously, we used telnet to reach the terminal server from our maintenance workstation. Now, the new one supports SSH, so we're finally moving off telnet. When logging into the terminal server via telnet, a user was... (0 Replies)
Discussion started by: jalburger
0 Replies

6. Cybersecurity

ssh to terminal server

Hi. We are currently upgrading the terminal server in our system (Solaris 8). Previously, we used telnet to reach the terminal server from our maintenance workstation. Now, the new one supports SSH, so we're finally moving off telnet. When logging into the terminal server via telnet, a user was... (3 Replies)
Discussion started by: jalburger
3 Replies

7. Solaris

how to connect a PC terminal to UNIX server?

Hi everyone, I am new to Unix and looking for help here. we have four terminals connected to our solaris server (x86 based). the server got an interface card which provide serial port and video port for all chained terminals in a serial way. All these clients have no IP and they all display... (3 Replies)
Discussion started by: Cheong
3 Replies

8. UNIX for Dummies Questions & Answers

Linux terminal server?

Hello everyone, I have an interesting project I'd like to implement on a Linux server here at work. Essentially, I'd like to replace a handful of Windows servers with a single Linux server. The only task these Windows servers perform, is provide remote desktops via RDP protocol that people... (13 Replies)
Discussion started by: lupin..the..3rd
13 Replies

9. Debian

How to exit debian server terminal?

I have an situation that are quite strange to me. I am not able to exit the server terminal and enter back into my home computer terminal by the command exit like I used to be able to exit the server terminal with before. I end up into my root shell again without even typing the root password like... (6 Replies)
Discussion started by: Jonathan Sander
6 Replies

10. Windows & DOS: Issues & Discussions

Start X Server without starting a terminal

when I run C:\cygwin\bin\run C:\cygwin\bin\startxwin.exe it fires up a terminal by default. Can I eliminate that terminal and start the x server as a service silently and sits in my status bar just there? Thanks Jack (0 Replies)
Discussion started by: lucky7456969
0 Replies
tanh(3M)																  tanh(3M)

NAME
tanh(), tanhf(), tanhl(), tanhw(), tanhq() - hyperbolic tangent functions SYNOPSIS
HP Integrity Server Only DESCRIPTION
returns the hyperbolic tangent of x. is a version of it takes a argument and returns a result. Integrity Server Only is a version of it takes a argument and returns a result. is an version of it takes an argument and returns an result. is equivalent to on HP-UX systems. USAGE
To use these functions, compile either with the default option or with the and the options. To use (for Integrity servers) or compile also with the option. To use any of these functions, make sure your program includes and link in the math library by specifying on the compiler or linker command line. For more information, see the at the following site: RETURN VALUE
If x If x is NaN, returns NaN. Whether raises the inexact exception is unspecified. ERRORS
No errors are defined. SEE ALSO
atanh(3M), cosh(3M), ctanh(3M), sinh(3M), math(5). STANDARDS CONFORMANCE
: SVID3, XPG4.2, ANSI C, ISO/IEC C99 (including Annex F, ``IEC 60559 floating-point arithmetic'') : ISO/IEC C99 (including Annex F, ``IEC 60559 floating-point arithmetic'') tanh(3M)
All times are GMT -4. The time now is 12:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy