01-21-2003
Found on Sunsolve (no login needed)
Annex Network Terminal Server
If you do a search for Annex terminal server, some other informational and free symptoms and resolutions can be found.
NOTE: An erpcd daemon must be running on the boot host before the
boot image can be downloaded. It is usually started via an
rc script, but may be run manually by executing /etc/erpcd.
See page 16 in the NTS Software Installation Notes.
Another link that may help out.
www.ofb.net
Last edited by RTM; 01-21-2003 at 12:45 PM..
10 More Discussions You Might Find Interesting
1. Solaris
Anyone know how to connect to a sun server using serial cable
my client PC is also a Sun !!!
I have the cable , just do not know how to start a terminal session in Sun . (1 Reply)
Discussion started by: civic2005
1 Replies
2. Solaris
All,
I have a problem with booting up of servers. I am involved in application programming(Perl/Shell), but don't have much hardware knowledge about the Sun Solaris Server's we use.
Our Development Servers are located at a remote place from the Development Centre. Every time there is a Power... (1 Reply)
Discussion started by: rahulrathod
1 Replies
3. UNIX for Advanced & Expert Users
hi all,
i have connected a new dump terminal to unix server.the connection is not direct.it is through a board. that is a board which contain lot of ports is connected to server. the terminals are connected to the board.when i connected the terminal to the server the message in terminal is like... (0 Replies)
Discussion started by: sujesh
0 Replies
4. Solaris
Hi there.
Anyone know how to get CPU speed, RAM size etc (basic specs) from a SUN server running solaris, from the unix terminal?
I'm sure there must be a command for this but ... I haven't been able to find it so far.. :o
Cheers. (8 Replies)
Discussion started by: kenny123m
8 Replies
5. Cybersecurity
Hi. We are currently upgrading the terminal server in our system (Solaris 8). Previously, we used telnet to reach the terminal server from our maintenance workstation. Now, the new one supports SSH, so we're finally moving off telnet. When logging into the terminal server via telnet, a user was... (0 Replies)
Discussion started by: jalburger
0 Replies
6. Cybersecurity
Hi. We are currently upgrading the terminal server in our system (Solaris 8). Previously, we used telnet to reach the terminal server from our maintenance workstation. Now, the new one supports SSH, so we're finally moving off telnet. When logging into the terminal server via telnet, a user was... (3 Replies)
Discussion started by: jalburger
3 Replies
7. Solaris
Hi everyone, I am new to Unix and looking for help here.
we have four terminals connected to our solaris server (x86 based).
the server got an interface card which provide serial port and video port for all chained terminals in a serial way. All these clients have no IP and they all display... (3 Replies)
Discussion started by: Cheong
3 Replies
8. UNIX for Dummies Questions & Answers
Hello everyone, I have an interesting project I'd like to implement on a Linux server here at work. Essentially, I'd like to replace a handful of Windows servers with a single Linux server. The only task these Windows servers perform, is provide remote desktops via RDP protocol that people... (13 Replies)
Discussion started by: lupin..the..3rd
13 Replies
9. Debian
I have an situation that are quite strange to me. I am not able to exit the server terminal and enter back into my home computer terminal by the command exit like I used to be able to exit the server terminal with before. I end up into my root shell again without even typing the root password like... (6 Replies)
Discussion started by: Jonathan Sander
6 Replies
10. Windows & DOS: Issues & Discussions
when I run C:\cygwin\bin\run C:\cygwin\bin\startxwin.exe it fires up a terminal by default. Can I eliminate that terminal and start the x server as a service silently and sits in my status bar just there? Thanks Jack (0 Replies)
Discussion started by: lucky7456969
0 Replies
LEARN ABOUT DEBIAN
webcommon.urlencode
WebCommon.urlEncode(3kaya) Kaya module reference WebCommon.urlEncode(3kaya)
NAME
WebCommon::urlEncode - URL encode a string
SYNOPSIS
String urlEncode( String x )
ARGUMENTS
x The string to encode
DESCRIPTION
URL encode a string. You should use this to encode reserved characters in URLs that you wish to be passed literally.
// trying to pass "http://www.example.com" as a parameter
url = "http://localhost/test.cgi?url=";
url += urlEncode("http://www.example.com");
// url = http://localhost/test.cgi?url=http%3A%2F%2Fwww.example.com
Note that in the example above, encoding the whole URL would be incorrect - that would create a relative URL beginning "http://".
AUTHORS
Kaya standard library by Edwin Brady, Chris Morris and others (kaya@kayalang.org). For further information see http://kayalang.org/
LICENSE
The Kaya standard library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public
License (version 2.1 or any later version) as published by the Free Software Foundation.
RELATED
WebCommon.urlDecode(3kaya)
Kaya October 2012 WebCommon.urlEncode(3kaya)