12-05-2002
Installing a SCSI controller... problems
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
2. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
3. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
6. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
7. Filesystems, Disks and Memory
I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI.
I can get as far as plugging it in on my own.
Please help
Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
8. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
ESIOP(4) BSD Kernel Interfaces Manual ESIOP(4)
NAME
esiop -- Enhanced Symbios Logic/NCR 53c8xx SCSI driver
SYNOPSIS
esiop* at pci? dev ? function ?
options SIOP_SYMLED
scsibus* at esiop?
DESCRIPTION
The esiop driver provides improved support over siop(4) for the Symbios Logic/NCR 53x8xx series of SCSI controller chips:
- 53c825 and 53c825a (Fast-Wide SCSI)
- 53c875 and 53c875j (Ultra-Wide SCSI)
- 53c876 (Dual Ultra-Wide SCSI)
- 53c885 (Ultra-Wide SCSI and Ethernet)
- 53c895 (Ultra2-Wide SCSI)
- 53c896 (PCI 64bit, dual Ultra2-Wide SCSI)
- 53c1010-33 (PCI 64bit, dual Ultra160 SCSI)
- 53c1510d (PCI 64bit, dual Ultra2-wide SCSI)
Older adapters are supported by the siop(4) driver.
The SIOP_SYMLED option causes the driver to report SCSI activity on the GPIO pin 1, which is connected to the activity LED on some adapters.
At this time only the 53c895 based Symbios and Tekram adapters are known to require this.
SEE ALSO
cd(4), ch(4), intro(4), pci(4), scsi(4), sd(4), siop(4), st(4), uk(4)
HISTORY
The esiop driver first appeared in NetBSD 1.6.
AUTHORS
The esiop driver was written by Manuel Bouyer <Manuel.Bouyer@lip6.fr> for NetBSD.
BSD
April 23, 2002 BSD