Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Network card problem, wrong IRQ
Top Forums UNIX for Dummies Questions & Answers Network card problem, wrong IRQ Post 31948 by Neo on Friday 15th of November 2002 09:36:13 AM
Old 11-15-2002
Sound like your kernel does not support the card. I would suggest you run the dmesg | more command and see if the kernel recognized your card when it booted. If not, you will have to check the linux h/w docs and see if your cards chipset is supported and rebuild the kernel to support this card.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Network Card Problem On Linux

Hi I just installed linux red hat 7.0 and i can't connect the machine on the network. Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize. Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies

3. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

5. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

6. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

7. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

8. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

9. Red Hat

Redhat disabling network interface - IRQ issue

Hi. I'm having problems on multiple Red Hat VM's (on esxi) whereby the network interface IRQ is disabled by the OS. This is the error from dmesg: command: Write(10): 2a 00 03 42 3f e0 00 00 08 00 mptscsih: ioc0: task abort: SUCCESS (sc=ffff81018b45c680) irq 67: nobody cared (try... (0 Replies)
Discussion started by: badoshi
0 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

LEARN ABOUT DEBIAN

network-admin

network-admin(1)					      General Commands Manual						  network-admin(1)

NAME

       network-admin - Network Administration Tool

SYNOPSIS

       network-admin [OPTION...]

DESCRIPTION

       network-admin is part of the GNOME system tools, a set of tools to easily access and manage system configuration.

       network-admin allows you to specify the way your system connects to other computers and to the Internet.

OPTIONS

       --display=DISPLAY
	      X display to use

       network-admin also accepts the standard GNOME and GTK options.

AUTHORS

       network-admin was written by Carlos Garnacho Parro <garnacho@tuxerver.net> and others.

       This manual page was written by Sven Arvidsson <sa@whiz.se>, for the Debian project (but may be used by others).

SEE ALSO

       services-admin(1), shares-admin(1), time-admin(1), users-admin(1), gtk-options(7), gnome-options(7)

       The online documentation available through the program's Help menu.

GNOME
								    2007-05-08							  network-admin(1)
All times are GMT -4. The time now is 02:44 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy