11-14-2002
routing table (netstat -rn)
Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system.
Thanks!
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can i set an permanent route so that itīs still here after a reboot ?
i have a gateways file
Thanks
:confused: :confused: :confused: (1 Reply)
Discussion started by: redcrosskbg
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies
3. IP Networking
hi all,
how to access ip routing table throgh program,
how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies
4. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
5. IP Networking
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Discussion started by: chanfle
3 Replies
6. IP Networking
Hi all,
I am confusing with routing table, i use linux and iptables.
i have 1 internet gateway, and 1 router for VPN.
here is my network.
eth0=192.168.0.1
eth1=192.168.100.1
192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet
|
... (4 Replies)
Discussion started by: blesets
4 Replies
7. Linux
Hello,
how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies
8. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
9. IP Networking
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Discussion started by: anid
0 Replies
10. HP-UX
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
LEARN ABOUT OSF1
ripquery
ripquery(8) System Manager's Manual ripquery(8)
NAME
ripquery - Queries RIP gateways
SYNOPSIS
/usr/sbin/ripquery [-1] [-2] [-[a5] authkey] [-n]
[-p] [-r] [-v] [-w time] gateway ...
FLAGS
Sends the query as a version 1 packet. Sends the query as a version 2 packet (default). Specifies the authentication password to use for
queries. If -a specified, an authentication type of SIMPLE will be used, if -5 is specified, an authentication type of MD5 will be used,
otherwise the default is an authentication type of NONE. Authentication fields in incoming packets will be displayed, but not validated.
Prevents the address of the responding host from being looked up to determine the symbolic name. Uses the RIP POLL command to request
information from the routing table. This is the default. If there is no response to the RIP POLL command, the RIP REQUEST command is
tried. The gated daemon responds to a POLL command with all the routes learned through RIP. Used the RIP REQUEST command to request
information from the gateway's routing table. Unlike the RIP POLL command, all gateways should support the RIP REQUEST. If there is no
response to the RIP REQUEST command, the RIP POLL command is tried. The gated daemon responds to a REQUEST command with all the routes he
announces out the specified interface. Because of limitations in the UDP interface, on systems based on BSD 4.3 Reno or earlier, REQUESTs
respond about the interface used to route packets back to the sender. This can be avoided by running ripquery on the host being queried.
Displays version information about ripquery before querying the gateways. Specifies the time in seconds to wait for the initial response
from a gateway. The default value is 5 seconds.
DESCRIPTION
The ripquery command is used to request all routes known by a RIP gateway by sending a RIP request or POLL command. The routing informa-
tion in any routing packets returned is displayed numerically and symbolically. The ripquery command is intended to be used as a tool for
debugging gateways, not for network management. SNMP is the preferred protocol for network management.
The ripquery command by default uses the RIP POLL command, which is an undocumented extension to the RIP specification supported by routed
on SunOS 3.x and later and by gated 1.4 and later. The RIP POLL command is preferred over the RIP REQUEST command because it is not sub-
ject to Split Horizon or Poisoned Reverse. See the RIP RFC for more information.
RELATED INFORMATION
Commands: gated(8), gdc(8), ospf_monitor(8), routed(8) delim off
ripquery(8)