11-14-2002
routing table (netstat -rn)
Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system.
Thanks!
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can i set an permanent route so that itīs still here after a reboot ?
i have a gateways file
Thanks
:confused: :confused: :confused: (1 Reply)
Discussion started by: redcrosskbg
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies
3. IP Networking
hi all,
how to access ip routing table throgh program,
how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies
4. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
5. IP Networking
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Discussion started by: chanfle
3 Replies
6. IP Networking
Hi all,
I am confusing with routing table, i use linux and iptables.
i have 1 internet gateway, and 1 router for VPN.
here is my network.
eth0=192.168.0.1
eth1=192.168.100.1
192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet
|
... (4 Replies)
Discussion started by: blesets
4 Replies
7. Linux
Hello,
how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies
8. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
9. IP Networking
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Discussion started by: anid
0 Replies
10. HP-UX
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
reboot(8) System Manager's Manual reboot(8)
NAME
reboot - Restarts the machine
SYNOPSIS
/usr/sbin/reboot [-dlnq]
DESCRIPTION
When the system is running and multiple users are logged in, use the shutdown -r command to perform a reboot operation. If no users are
logged in, use the reboot command.
The reboot command normally stops all running processes, syncs the disks, logs the reboot, and writes a shutdown entry in the login
accounting file, /var/adm/wtmp.
The reboot command uses the sync call to synchronize the disks, and to perform other shutdown activities such as resynchronizing the hard-
ware time-of-day clock. After these activities, the system reboots. By default, the system starts and the file systems are automatically
checked. If the start-up activities are successful, the system comes up in the default run-level.
You must have root privileges to use this command. Using the -n flag can result in file system damage.
FLAGS
Generates a crash dump of the system before halting it. Can be used with any of the other flags. Does not log the reboot using syslog
Does not sync the disks or log the reboot using syslog Performs a quick reboot without first shutting down running processes; does not log
the reboot using syslog
EXAMPLES
To enable the default reboot action, enter: reboot This command causes the system to stop all running processes, sync the disks, log the
shutdown, and perform other routine shutdown and reboot activities. To shut down the system without logging the reboot, enter: reboot -l
This command shuts down the system and performs all shutdown and reboot activities, except logging the shutdown. To reboot the system
abruptly, enter: reboot -q This command reboots the system abruptly without shutting down running processes.
FILES
Specifies the command path Specifies the login accounting file Specifies the path of the syslog daemon
RELATED INFORMATION
Commands: fsck(8), halt(8), init(8), savecore(8) shutdown(8), syslogd(8)
Functions: reboot(2), sync(2), syslog(3) delim off
reboot(8)